You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool | |
|
Motor wizard settings by ESCam on Thu, 2018-11-08 22:49 |
8 |
by dtp Mon, 2023-11-20 00:49 |
VESC Tool | |
|
4 BLDC for 1 VESC by mac_cros on Wed, 2019-03-20 16:45 |
8 |
by tul00985 Wed, 2019-04-03 08:32 |
Third Party Hardware | |
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
|
VESC Battery Packs by frank on Tue, 2020-10-13 15:21 |
8 |
by zhivko Sat, 2024-08-10 21:14 |
General discussion | |
|
Fimware 5.1 - where is the VESC_servoout.bin? by JackSilb on Tue, 2020-04-28 06:37 |
8 |
by udayravuri Tue, 2023-03-28 00:08 |
VESC Firmware | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
No connection with vesc by Matthieu van Ra... on Wed, 2019-02-13 18:07 |
8 |
by sam.vanratt Thu, 2019-02-14 15:33 |
General discussion | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
VESC 6 Feature Requests by josh on Wed, 2017-06-28 06:53 |
8 |
by Enak Mon, 2017-07-03 15:38 |
VESC6 Beta | |
|
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
|
Low power VESC - any available by wdaehn on Wed, 2018-02-28 18:02 |
9 |
by TechAUmNu Mon, 2018-03-19 11:54 |
Third Party Hardware | |
|
Problem with Bluetooth connection (HM-10) by squdowx on Mon, 2018-07-30 15:56 |
9 |
by CTSchorsch Thu, 2019-12-05 21:27 |
General discussion | |
|
Invert motor direction. by Sanjoy on Thu, 2017-06-15 23:31 |
9 |
by Roger Wolff Mon, 2017-06-19 16:00 |
VESC6 Beta | |
|
Noise with Hall sensor at high speed by yosoufe on Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
General discussion | |
|
Firmware for 4.xx VESC in new VESC Tool? by sl33py on Wed, 2017-06-28 21:27 |
9 |
by sl33py Fri, 2017-07-14 08:29 |
VESC6 Beta | |
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
Problems with Initial flash of Hw4:12 by Idoff on Mon, 2018-04-16 18:47 |
9 |
by Frankfartin2077 Thu, 2019-04-04 10:10 |
VESC Firmware | |
|
Serial Connection Lost with Vesc6.6 Firmware 5.2 and Vesc Tool 3.0 by Dan Slanker on Wed, 2021-04-28 16:56 |
9 |
by AngelKillR Wed, 2022-09-28 05:10 |
General discussion |
Pages
