You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
VESC Tool Error - updating fw on old hw 4.7 VESCs by sl33py on Sun, 2017-07-09 05:43 |
17 |
by bboyspoons Wed, 2024-02-07 19:50 |
VESC6 Beta | |
Current Sensing in VESC by Toshi Sharma on Fri, 2021-11-26 08:51 |
17 |
by Toshi Sharma Tue, 2022-01-04 11:46 |
General discussion | |
VESC-Project Open Source status ? by Pimousse on Tue, 2018-01-23 11:41 |
18 |
by velolac Thu, 2023-02-09 11:33 |
The VESC-Project | |
Current out of Sync by CTSchorsch on Sat, 2020-08-01 13:24 |
18 |
by CTSchorsch Fri, 2020-09-04 11:28 |
Third Party Hardware | |
CAN bus support not enabled in this build of vesc tool? by Tsomo on Fri, 2021-10-01 09:48 |
18 |
by merten Fri, 2024-08-09 18:14 |
VESC Tool | |
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
18 |
by Chris Barth Fri, 2023-11-10 04:45 |
General discussion | |
VESC with really high KV by bengce on Sun, 2020-06-21 11:18 |
18 |
by bengce Thu, 2020-08-13 14:11 |
General discussion | |
Battery Questions? by Grimjovv on Mon, 2017-06-12 08:21 |
19 |
by sl33py Thu, 2017-07-06 01:52 |
VESC6 Beta | |
UART communication by EthB on Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
General discussion | |
Motor Values in VESC-Tool 2019 by frank on Wed, 2019-02-27 09:40 |
19 |
by Onarb Kabr Wed, 2025-01-15 13:28 |
VESC Tool | |
High Voltage ESC (HiVEsc) 150V 500A by e-biker on Thu, 2019-08-15 14:45 |
19 |
by jarrancho Fri, 2020-12-04 11:35 |
Third Party Hardware | |
Is electronic brake always REGEN? by Tilman Baumann on Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
General discussion | |
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
19 |
by Artabotak Tue, 2024-12-03 08:48 |
General discussion | |
DRV8302 sensibility by lurch on Sat, 2021-10-23 23:37 |
19 |
by lurch Sat, 2021-10-30 10:13 |
General discussion | |
Using a VESC V4.12 for a machining lathe by Krampas on Sun, 2019-06-09 22:16 |
19 |
by Luke264 Wed, 2021-02-17 18:53 |
General discussion | |
Efficiency Control by devin on Sat, 2018-09-29 19:50 |
19 |
by devin Wed, 2019-07-10 19:35 |
General discussion | |
VESC CNC case - Feedbacks by Pimousse on Wed, 2017-06-07 17:58 |
19 |
by Necromenz Mon, 2017-06-12 23:44 |
VESC6 Beta | |
Bluetooth 4 remote by bob23 on Fri, 2020-09-04 02:19 |
20 |
by vadicus Mon, 2020-09-14 22:14 |
Third Party Hardware | |
Vesc 6 motor setup fault by Davo69URX on Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
General discussion | |
Dual VESC with UART communication (Arduino) - how to communicate with slave over can ? by GargiMan on Thu, 2019-01-03 01:56 |
21 |
by Shubham07 Fri, 2023-03-31 10:49 |
General discussion |
Pages
