You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
ERPM settings restrict carving speed on outer wheel. Poor user experience. by Paul15578 on Fri, 2018-01-12 02:28 |
9 |
by Ackmaniac Tue, 2018-04-24 13:47 |
General discussion | |
|
Problem with burned FETs and drivers after reconnect battery by CTSchorsch on Sat, 2021-01-16 19:49 |
9 |
by CTSchorsch Wed, 2021-02-17 13:42 |
Third Party Hardware | |
|
PPM with ADC by vufmihai on Mon, 2019-12-30 09:09 |
10 |
by k3ff Sat, 2024-05-11 19:09 |
Feature Requests | |
|
First impressions to the new VESC Tool software by hexakopter on Fri, 2017-05-26 21:19 |
10 |
by Roger Wolff Sun, 2017-06-11 06:27 |
VESC6 Beta | |
|
FOC current oscillation at max. speed by ProgramThyself on Mon, 2020-08-10 05:55 |
10 |
by SRFirefox Wed, 2020-08-26 23:10 |
General discussion | |
|
VESC4.12 new fmw issue by jsy070913 on Thu, 2017-09-07 04:26 |
10 |
by Silverline Sat, 2017-09-30 08:42 |
VESC Firmware | |
|
Brakes completely repeatedly failing at high temperature by Paul15578 on Mon, 2018-03-26 13:06 |
10 |
by Paul15578 Sun, 2018-04-22 14:16 |
General discussion | |
|
Dual VESC, Dual UART? by kneave on Mon, 2020-08-17 22:00 |
10 |
by Duane Degn Mon, 2020-08-24 00:23 |
General discussion | |
|
When 100250 is not enough by eptv on Sat, 2021-12-11 14:38 |
10 |
by eptv Wed, 2021-12-15 20:53 |
VESC Original Hardware | |
|
VESC BMS Hardware Reference Design by DubP on Fri, 2021-09-03 21:00 |
10 |
by frank Wed, 2022-08-03 14:34 |
VESC Original Hardware | |
|
Few questions by ElectroMagneto on Thu, 2020-01-09 23:57 |
10 |
by ElectroMagneto Sat, 2020-01-11 00:45 |
General discussion | |
|
about reference hardware by qdxiatao on Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
General discussion | |
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
General discussion | |
|
Noised signal from motor NTC sensor | HW4.12 FW3.27 by ma-j-sterelektron on Wed, 2017-09-06 18:41 |
10 |
by vescsci Wed, 2020-07-15 22:47 |
General discussion | |
|
VESC Questions from the newbie by mendez on Fri, 2019-02-08 21:13 |
10 |
by frank Mon, 2019-02-18 08:52 |
General discussion | |
|
Switching frequency factor 2 lower by Elwin on Sat, 2021-11-13 22:48 |
10 |
by Elwin Sun, 2022-01-09 08:31 |
General discussion | |
|
Detection failed. Reason: -11 by Eco Delsbo on Fri, 2019-05-03 12:01 |
10 |
by Gatze Wed, 2020-03-18 22:04 |
VESC Tool | |
|
Insufficient torque at low RPM by isso777 on Sat, 2022-04-23 21:13 |
10 |
by frank Tue, 2022-05-03 08:18 |
General discussion | |
|
I made a Boost Current Mod by JL2579 on Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
VESC Tool | |
|
Suddenly broken by moto_guy on Fri, 2019-03-08 13:50 |
10 |
by David_1 Fri, 2022-06-17 21:07 |
General discussion |
Pages
