You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees on Tue, 2022-01-18 22:57 |
by christian.lees Tue, 2022-01-18 22:57 |
General discussion | ||
|
VESC "underpowered" vs Kunteng Controller experience by andyw2005 on Thu, 2021-10-21 23:54 |
1 |
by Elwin Fri, 2021-10-22 11:39 |
General discussion | |
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 on Fri, 2017-10-06 03:39 |
2 |
by frank Mon, 2017-10-09 19:51 |
General discussion | |
|
VESC for small drone (<1kg) by iKrosoft on Wed, 2018-10-03 16:40 |
3 |
by arvidb Thu, 2018-10-04 21:05 |
General discussion | |
|
Controlling VESC with arduino - by vulkan66 on Thu, 2019-07-11 11:51 |
3 |
by vulkan66 Thu, 2019-08-01 21:34 |
General discussion | |
|
Need Help with single FSESC running a BDUAV 6384 120KV & 12v SLA Batt Setup by KJB on Fri, 2022-01-07 02:43 |
1 |
by skyline1970 Tue, 2022-01-18 10:39 |
General discussion | |
|
step by step ebike thorttle setup by sindre on Wed, 2019-07-03 17:59 |
by sindre Wed, 2019-07-03 17:59 |
General discussion | ||
|
Issue in encoder mode by limeng06217 on Tue, 2020-02-25 16:48 |
2 |
by limeng06217 Tue, 2020-02-25 16:56 |
General discussion | |
|
Complete lack of torque on DIY e-bike by Frazatto on Fri, 2020-09-18 21:01 |
6 |
by tonyXHB Tue, 2020-12-22 13:18 |
General discussion | |
|
Set RPM - reverse direction over CAN-Bus by 65273 on Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
General discussion | |
|
Need help with brushed fc 24 bolt motor control by searth on Sun, 2022-12-18 16:05 |
by searth Sun, 2022-12-18 16:05 |
General discussion | ||
|
FAULT_CODE_HIGH_OFFSET_CURRENT_SENSOR_3 by TB_Poule on Sat, 2021-04-10 17:26 |
10 |
by Mohanangappan Wed, 2024-09-18 16:20 |
General discussion | |
|
Cant connect to Flipsky 75100 by Ed222 on Sun, 2022-03-20 00:31 |
5 |
by wimleo Wed, 2025-03-19 17:51 |
General discussion | |
|
Power cutoff without any warning by TylerWilson on Fri, 2022-12-09 06:37 |
by TylerWilson Fri, 2022-12-09 07:11 |
General discussion | ||
|
which configuration file I should change to make operate a VESC at 800 Volts by JCordova on Tue, 2024-02-06 17:49 |
1 |
by NOAI Wed, 2024-02-07 15:54 |
General discussion | |
|
NRF Implementation by Christian on Thu, 2018-02-15 14:36 |
by Christian Thu, 2018-02-15 14:36 |
General discussion | ||
|
IMU support and alternate IMU ICs (Bosch bmi160?) by shaman on Fri, 2019-09-20 15:04 |
2 |
by shaman Thu, 2019-10-03 19:06 |
General discussion | |
|
Stuttering Motor by Pollmann Andreas on Wed, 2021-07-21 23:54 |
by Pollmann Andreas Wed, 2021-07-21 23:54 |
General discussion | ||
|
just receaved my awesome new vesc 6 plus however it wont configurate i get an errot message. :( by sabladask on Wed, 2023-05-03 16:15 |
2 |
by frank Fri, 2023-05-05 20:54 |
General discussion | |
|
VESC Hardware link broken by jparadie on Mon, 2018-06-18 12:21 |
1 |
by frank Fri, 2018-06-22 11:33 |
General discussion |
Pages
