You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
UART Safety Feature by jaghori.sasan on Wed, 2019-09-04 18:45 |
by jaghori.sasan Wed, 2019-09-04 18:45 |
VESC Tool | ||
|
VESCTOOL - Multiple VESC simultaneous configuration (Same CANBUS ID issues) by Filcas on Thu, 2021-02-18 20:52 |
2 |
by Filcas Fri, 2021-02-19 01:37 |
VESC Tool | |
|
Dual VESC and One Motor Stops Spinning by f0n on Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
VESC Tool | |
|
pulsation at mid speed by smallbikefun on Sun, 2024-05-12 19:00 |
2 |
by Lizzle Wed, 2024-09-04 06:07 |
VESC Tool | |
|
Motor whine with HFI? by christopher.h.poole on Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
VESC Tool | |
|
FSESC seems to be speed limiting my motor by 5amsung4 on Sat, 2022-09-03 18:50 |
by 5amsung4 Mon, 2022-09-05 07:51 |
VESC Tool | ||
|
Low RPM motor stutter? by ebikerevolution on Mon, 2019-01-21 20:06 |
8 |
by Tibor Kalman Za... Sat, 2021-02-13 13:59 |
VESC Tool | |
|
Keyboard control not working (Remote works) by bukl on Sun, 2020-05-24 16:51 |
6 |
by sanketh1691 Wed, 2021-10-06 20:45 |
VESC Tool | |
|
Can't get Dual drive/CAN bus working by Xadiant on Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
VESC Tool | |
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried on Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
VESC Tool | |
|
PPM mapping not working by Andytttt on Thu, 2020-01-09 05:58 |
1 |
by frank Mon, 2020-01-27 21:06 |
VESC Tool | |
|
Dual Motor Setup Wizard Not working 1.08 by captclearleft on Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
VESC Tool | |
|
Running a DC 12V trolling motor with a 4.20. Hidden current limit?. by Impuls60 on Wed, 2020-07-22 14:32 |
by Impuls60 Wed, 2020-07-22 19:00 |
VESC Tool | ||
|
Help with more torque with vesc by Juzy on Wed, 2025-04-02 04:52 |
by Juzy Wed, 2025-04-02 06:59 |
VESC Tool | ||
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh on Wed, 2023-04-26 16:13 |
5 |
by Nshoup Sat, 2026-01-10 01:30 |
VESC Tool | |
|
VESC tool and sk8-esc V6 set up shows incorrectcurrent usage by DominykasS on Fri, 2022-09-30 13:54 |
2 |
by Frizzaper Wed, 2023-11-15 04:25 |
VESC Tool | |
|
Sampled Data not working by ben5243 on Tue, 2019-02-19 20:12 |
6 |
by emntz Thu, 2024-02-08 16:35 |
VESC Tool | |
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning on Mon, 2024-12-02 13:19 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
VESC Tool |
Pages
