You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
motor not running smoothly, it makes little "steps" by nomadaomni on Mon, 2024-11-18 15:08 |
2 |
by nomadaomni Tue, 2024-11-19 12:51 |
General discussion | |
|
Balance App Info by NuRxG on Tue, 2020-11-17 21:07 |
1 |
by triff69 Wed, 2024-11-20 10:51 |
Balance App (for EUCs - Electric Unicycles) | |
|
Communicate to VESC with ESP32/Arduino by semeat on Thu, 2024-08-22 08:24 |
3 |
by Kaeomangkon Fri, 2024-11-22 07:39 |
Projects incorporating VESC technology | |
|
Using UART for FSESC by Kostya1875 on Thu, 2024-09-26 19:07 |
1 |
by Nineballshot Mon, 2024-11-25 02:04 |
General discussion | |
|
speed by ELRIOP on Sun, 2024-09-08 15:24 |
1 |
by Nineballshot Mon, 2024-11-25 02:20 |
General discussion | |
|
How to connect 5 Pin Hall Sensor to 6 Pin Hall Sensor Connector by tinytuna38 on Thu, 2024-06-20 20:56 |
2 |
by Nineballshot Mon, 2024-11-25 02:38 |
General discussion | |
|
Issues with running bldc motor (Motor screeching) by mansi712 on Mon, 2024-08-26 12:10 |
1 |
by Nineballshot Mon, 2024-11-25 02:43 |
General discussion | |
|
Use IMU for keeping direction by arnolde on Mon, 2024-11-25 11:12 |
by arnolde Mon, 2024-11-25 11:19 |
General discussion | ||
|
Adafruit Feather nRF52 <> VESC BLE? by NoeI on Mon, 2024-06-17 22:57 |
2 |
by Onarb Kabr Mon, 2024-11-25 13:32 |
General discussion | |
|
Help needed VESC - Update missed? by JUST1975 on Tue, 2024-11-26 11:43 |
1 |
by JUST1975 Tue, 2024-11-26 11:53 |
VESC Firmware | |
|
150KW VESC by paltatech on Sun, 2017-09-10 23:11 |
40 |
by Artabotak Wed, 2024-11-27 11:15 |
General discussion | |
|
HIGH Voltage (350v-450v) VESC by athlon on Sun, 2018-11-25 18:34 |
8 |
by Artabotak Wed, 2024-11-27 12:30 |
Third Party Hardware | |
|
Makerbase VESC 84200HP It won't turn on. by Deejii23 on Sun, 2024-11-24 16:31 |
1 |
by Deejii23 Thu, 2024-11-28 18:58 |
Third Party Hardware | |
|
Someone please help by Mark griffin on Thu, 2024-08-01 14:29 |
2 |
by Onarb Kabr Sun, 2024-12-01 17:20 |
General discussion | |
|
SINE/COS encoder makes motor not work by DHOUT on Mon, 2023-01-30 05:23 |
1 |
by Jamesstudio Sun, 2024-12-01 17:56 |
General discussion | |
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning on Mon, 2024-12-02 13:19 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
VESC Tool | ||
|
wrong amps reading (realtime data) by flez1966 on Wed, 2024-03-27 13:55 |
2 |
by B1996 Tue, 2024-12-03 07:26 |
Third Party Hardware | |
|
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
19 |
by Artabotak Tue, 2024-12-03 08:48 |
General discussion | |
|
Tach output changes when switching from BLDC --> FOC by Zoxks on Sun, 2024-12-01 20:28 |
1 |
by Zoxks Tue, 2024-12-03 19:10 |
General discussion | |
|
Spintend v2 100amp 100volt by Phill Dixon on Wed, 2024-12-04 18:14 |
1 |
by electricfox Wed, 2024-12-04 20:06 |
General discussion |
Pages
