You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
advice on position control by feskarn on Mon, 2021-02-15 14:47 |
by feskarn Mon, 2021-02-15 14:47 |
General discussion | ||
|
Setting the motor parameters by Lenar on Sat, 2024-05-04 10:18 |
by Lenar Sat, 2024-05-04 10:18 |
General discussion | ||
|
Device shutting down by gjos on Sun, 2024-04-21 22:23 |
by gjos Sun, 2024-04-21 22:23 |
General discussion | ||
|
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:04 |
by ruthvikchanda Thu, 2018-12-06 07:04 |
VESC6 Beta | ||
|
"Allow Breaking" set to "TRUE" when "Backup COnfigurations (Including CAN) by bayetan on Mon, 2023-05-22 05:33 |
by bayetan Mon, 2023-05-22 05:33 |
VESC Tool | ||
|
Please help, problems with brand new vesc 6 pluss. by sabladask on Fri, 2023-05-05 15:08 |
by sabladask Fri, 2023-05-05 15:08 |
VESC Original Hardware | ||
|
If the PPM line is completely destroyed, is it possible to program another one? by Nickicook4noswag on Tue, 2024-06-25 05:57 |
by Nickicook4noswag Tue, 2024-06-25 05:57 |
General discussion | ||
|
Log ADC Feature by BITI on Mon, 2023-11-13 14:58 |
by BITI Mon, 2023-11-13 14:58 |
Feature Requests | ||
|
What constitutes a continuous vs burst current? by Alistair Goodman on Tue, 2025-01-07 16:08 |
by Alistair Goodman Tue, 2025-01-07 16:08 |
General discussion | ||
|
adiv5.h adiv5_dp_abort function confusion by dsppower on Sun, 2022-05-08 19:26 |
by dsppower Sun, 2022-05-08 19:26 |
VESC Firmware | ||
|
Single shunt by andreas on Wed, 2018-09-12 22:17 |
by andreas Wed, 2018-09-12 22:17 |
Feature Requests | ||
|
Is it normal to have5th harmonic current ? by Alex Marques on Fri, 2023-02-10 16:01 |
by Alex Marques Fri, 2023-02-10 16:02 |
General discussion | ||
|
Newer DRV8353RS instead of DRV8301? by whydoilive on Fri, 2021-04-02 10:13 |
by whydoilive Fri, 2021-04-02 10:13 |
VESC6 Beta | ||
|
Full Brake vs Switch Off by meisterpro on Mon, 2021-03-22 14:36 |
by meisterpro Mon, 2021-03-22 14:36 |
VESC Tool | ||
|
terminal command via UART for a gimbal by fredfred on Sat, 2021-12-18 20:49 |
by fredfred Sat, 2021-12-18 20:49 |
VESC Tool | ||
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Motors spin during detection but then won't spin by jsbenson on Tue, 2023-06-27 23:54 |
by jsbenson Tue, 2023-06-27 23:54 |
General discussion | ||
|
Reverse Button Status over UART? by Rich235 on Sat, 2024-09-07 10:34 |
by Rich235 Sat, 2024-09-07 10:34 |
General discussion | ||
|
Can't find good parameters for FOC detection by Kabroc on Thu, 2020-04-30 16:28 |
by Kabroc Thu, 2020-04-30 16:28 |
VESC Tool | ||
|
Switchign frequency issue? by Maxid on Thu, 2020-12-03 11:47 |
by Maxid Thu, 2020-12-03 11:47 |
VESC Firmware |
Pages
