You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Spikes in RPM causing the ride to be bumpy by dsuresh on Tue, 2021-03-23 21:55 |
by dsuresh Tue, 2021-03-23 21:55 |
General discussion | ||
VESC efficency in position vs speed mode by vadimz on Mon, 2021-12-20 15:04 |
2 |
by Elwin Mon, 2022-01-03 19:23 |
General discussion | |
temperature compensation make sense? by alexshen2012 on Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
General discussion | |
AS5047 over SPI pins on VESC six by Jessica on Fri, 2018-12-21 11:10 |
by Jessica Fri, 2018-12-21 11:10 |
General discussion | ||
Rc controller more than one input ? by zebb.guy@moshon... on Tue, 2022-07-26 14:51 |
2 |
by zebb.guy@moshon... Wed, 2022-07-27 17:22 |
General discussion | |
external IMU vesc wiring by surfer on Wed, 2019-09-04 21:44 |
6 |
by TechAUmNu Fri, 2023-03-10 14:59 |
General discussion | |
stm32/vesc fault limit? by 123seaborder on Sat, 2020-11-21 16:37 |
1 |
by vadicus Sun, 2020-11-22 04:13 |
General discussion | |
Max Batt current and max motor current by Inewton on Mon, 2021-06-21 14:43 |
1 |
by spacewalker Tue, 2021-06-22 08:21 |
General discussion | |
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb on Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
General discussion | |
AS5048A and the AS5047D Problems. by raess on Wed, 2018-04-04 14:05 |
2 |
by liqikai Thu, 2018-09-13 10:47 |
General discussion | |
Vesc board on ebike by tailele on Sat, 2020-11-14 15:08 |
2 |
by tonyXHB Tue, 2020-12-22 12:21 |
General discussion | |
VESC not responding to throttle by posthy on Thu, 2022-03-10 17:12 |
1 |
by skyline1970 Mon, 2022-03-14 20:37 |
General discussion | |
Motor Driver Voltage Spike Problem by sersam on Sat, 2022-11-12 19:23 |
1 |
by skyline1970 Thu, 2022-11-24 20:00 |
General discussion | |
Which encoders are supported? by raess on Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
General discussion | |
Would like VESC 4.12 repair tips by spork on Wed, 2019-04-03 04:53 |
6 |
by spork Tue, 2019-04-23 11:01 |
General discussion | |
Issue with VESC I/O on donkey car by baluja on Fri, 2022-10-28 02:56 |
by baluja Fri, 2022-10-28 02:56 |
General discussion | ||
how do you update the vesc tool by Phill Dixon on Fri, 2017-09-29 10:58 |
1 |
by ThierryGTLTS Fri, 2017-09-29 16:43 |
General discussion | |
VESC recommendation for sailboat conversion by Henque19 on Thu, 2019-11-28 00:42 |
9 |
by Henque19 Fri, 2019-12-20 16:15 |
General discussion | |
Runaway Motor with No BLE by Marctwo on Thu, 2020-07-02 20:47 |
by Marctwo Thu, 2020-07-02 20:47 |
General discussion | ||
How to control PPM output with CANBUS command by JiaheXu on Thu, 2023-03-30 20:21 |
2 |
by JiaheXu Wed, 2023-04-05 16:52 |
General discussion |