You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Understanding Dual VESC (dual motors) setups by Cham on Mon, 2020-09-21 18:45 |
6 |
by hemmadroid Thu, 2025-03-06 06:34 |
General discussion | |
|
(SOLVED) I2C, change pins by CTSchorsch on Mon, 2020-05-25 07:59 |
6 |
by woodmastr Tue, 2023-06-06 15:57 |
VESC Firmware | |
|
Vesc Six won't run or flash firmware by Grimjovv on Wed, 2017-07-19 07:49 |
6 |
by Danny Bokma Thu, 2017-08-03 23:29 |
VESC6 Beta | |
|
VESC 4.12 in a CityEL by twikis on Fri, 2018-01-12 15:54 |
6 |
by Roger Wolff Sat, 2018-01-20 16:14 |
General discussion | |
|
VESC minimum RPM by askker on Thu, 2019-07-11 05:03 |
6 |
by Artius Reynolds Sun, 2020-10-18 23:25 |
General discussion | |
|
builtin ble on vesc 75_300 by alexefoil on Wed, 2019-07-03 02:35 |
6 |
by Glennisoty Thu, 2021-04-15 05:31 |
VESC Original Hardware | |
|
Torque control with PWM at 10kHz for LinuxCNC + MESA + AC servo by antonchromjak on Tue, 2018-03-06 08:01 |
6 |
by Artabotak Sat, 2024-01-06 09:24 |
General discussion | |
|
Custom hardware by aachner on Thu, 2019-12-19 15:15 |
6 |
by Jens Sun, 2025-02-02 22:39 |
Third Party Hardware | |
|
Vesc PAS (Pedal Assist) by Evwan on Sat, 2022-07-02 04:37 |
6 |
by wraven Wed, 2025-05-07 14:40 |
VESC Tool | |
|
Watch Display by vadicus on Tue, 2020-06-16 08:21 |
6 |
by kevingraehl Sat, 2025-10-11 06:32 |
Third Party Hardware | |
|
is Cross Coupling power limitation? by ziumus on Sat, 2021-02-06 15:57 |
6 |
by ziumus Sat, 2021-02-27 16:08 |
General discussion | |
|
I Need Some Guidance With My Schematic 16s 50a by qwerasdf on Sat, 2022-01-01 15:04 |
6 |
by mckenzie.keith Fri, 2022-01-14 04:39 |
Third Party Hardware | |
|
VESC 100/250 won't go full duty cycle by TheBennis on Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
VESC Original Hardware | |
|
ERPM, the RPM on the motor does not change by hopeingod on Fri, 2024-05-10 11:15 |
6 |
by hopeingod Mon, 2024-05-13 20:45 |
VESC Tool | |
|
I have the BLUEZ... Or rather... I don't. by Roger Wolff on Wed, 2018-01-03 16:03 |
6 |
by arvidb Wed, 2018-01-17 14:26 |
VESC Tool | |
|
UART for NRF51822 on "old" nrf pins ? by CTSchorsch on Fri, 2019-11-29 16:41 |
6 |
by hl0dk0 Tue, 2022-08-16 12:46 |
Feature Requests | |
|
PAS 3-wire sensor : possible to check a digital input under VESC-toool? by marc426 on Wed, 2021-10-27 00:26 |
6 |
by velolac Thu, 2021-11-25 20:09 |
General discussion | |
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie on Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
General discussion | |
|
Alternate for STM32F405 Microcontroller by gowrav on Fri, 2021-06-18 07:44 |
6 |
by damien31 Wed, 2023-05-24 13:01 |
General discussion | |
|
Lack of throttle control / too fast by mgisch on Mon, 2019-04-01 05:57 |
6 |
by mgisch Wed, 2019-04-03 09:53 |
Third Party Hardware |
Pages
