You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Motor and input calibration without drive train by technique on Tue, 2020-07-14 19:22 |
by technique Tue, 2020-07-14 19:22 |
VESC Tool | ||
|
KERS system with a VESC 100/250 MKIII by Simone Succi on Thu, 2026-02-26 08:28 |
by Simone Succi Thu, 2026-02-26 16:20 |
General discussion | ||
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
|
Current control performance & best way to tune Kp and Ki by jinwonchung on Thu, 2024-10-17 15:52 |
by jinwonchung Thu, 2024-10-17 15:53 |
General discussion | ||
|
Need help with auto power off and ADC by dsuresh on Wed, 2021-03-17 21:45 |
by dsuresh Wed, 2021-03-17 21:45 |
General discussion | ||
|
HFI Tuning - "Start Voltage" Question by drummerboy5408 on Sat, 2022-11-12 03:12 |
by drummerboy5408 Sat, 2022-11-12 03:12 |
General discussion | ||
|
Position Control with Resolver by robo_studienarbeit on Tue, 2018-10-16 18:57 |
by robo_studienarbeit Tue, 2018-10-16 18:57 |
General discussion | ||
|
Dual Vesc reading second wheel RPM by rdavenport3 on Tue, 2022-05-03 15:32 |
by rdavenport3 Tue, 2022-05-03 15:32 |
VESC Firmware | ||
|
Issues running a gimbal motor by ksau on Thu, 2021-03-11 16:44 |
by ksau Thu, 2021-03-11 16:44 |
General discussion | ||
|
VESC Tool speed control overshoot by PKmita on Tue, 2022-04-26 16:05 |
by PKmita Tue, 2022-04-26 16:12 |
VESC Tool | ||
|
Vesc tool shows wrong voltage by anythingstl on Wed, 2024-02-14 20:06 |
by anythingstl Wed, 2024-02-14 20:06 |
VESC Tool | ||
|
Detection for a drone outrunner 515 kV and 775 kV by MaksK on Thu, 2020-06-04 16:05 |
by MaksK Thu, 2020-06-04 16:05 |
VESC Tool | ||
|
Comms plug and leads by craig w on Fri, 2021-12-24 00:25 |
by craig w Fri, 2021-12-24 00:25 |
General discussion | ||
|
Spin motor at constant ERPM while a button is pressed by t-dub-maui on Fri, 2024-01-26 07:33 |
by t-dub-maui Fri, 2024-01-26 07:33 |
General discussion | ||
|
VESC PAS sensor connection, which pins? by matajumotors on Fri, 2021-05-28 12:37 |
by matajumotors Fri, 2021-05-28 12:37 |
General discussion | ||
|
Basic VESC troubleshooting (postmortem?) by N_COUNTER on Tue, 2023-03-14 10:58 |
by N_COUNTER Tue, 2023-03-14 11:01 |
General discussion | ||
|
FSESC seems to be speed limiting my motor by 5amsung4 on Sat, 2022-09-03 18:50 |
by 5amsung4 Mon, 2022-09-05 07:51 |
VESC Tool | ||
|
Flipsky 75100 V2 with Maxon 386675 by GoFast99 on Thu, 2025-06-05 20:54 |
by GoFast99 Thu, 2025-06-05 20:54 |
Third Party Hardware | ||
|
servo input by Roger Wolff on Tue, 2018-07-03 07:50 |
by Roger Wolff Tue, 2018-07-03 07:50 |
VESC Firmware | ||
|
Sensorless Homing: Move motor between two endstops by LISMS on Fri, 2025-05-09 00:50 |
by LISMS Fri, 2025-05-09 00:50 |
Projects incorporating VESC technology |
Pages
