You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
What is limiting the speed? by ProgramThyself on Wed, 2021-10-06 20:07 |
7 |
by ProgramThyself Sun, 2021-10-17 19:08 |
General discussion | |
|
Here lies the thread for hardware powered by stm32 by neo on Tue, 2021-06-15 00:47 |
7 |
by neo Tue, 2021-06-15 01:43 |
Third Party Hardware | |
|
hybrid helicopter engine vesc6 bldc settings by artteth on Wed, 2017-09-13 01:11 |
7 |
by matteogalet Tue, 2022-06-14 21:50 |
VESC6 Beta | |
|
Wand and VESC profiles by djevIen on Fri, 2019-09-13 09:22 |
7 |
by f0n Tue, 2025-02-11 01:47 |
Feature Requests | |
|
Endless mode (as Mellow boards have) by Oyta on Mon, 2018-04-16 19:05 |
7 |
by Jcowell Mon, 2020-06-08 22:13 |
Feature Requests | |
|
built Firmware is too large by maxhertz on Thu, 2022-02-03 08:37 |
7 |
by dpeinado Thu, 2022-06-23 12:39 |
VESC Firmware | |
|
HW 4.12 Change low voltage cutoff by subodh.malgonde on Tue, 2018-09-18 07:31 |
7 |
by TheFallen Thu, 2018-09-20 09:51 |
VESC Original Hardware | |
|
Fault code drv by Dominik139 on Wed, 2022-05-04 09:16 |
7 |
by frank Fri, 2022-05-06 08:02 |
General discussion | |
|
Maytech 75/300 R2 v.6.02 fault by Ai on Thu, 2024-05-30 17:16 |
7 |
by Ai Wed, 2024-07-03 20:42 |
VESC6 Beta | |
|
How to get vesc tool for linux on ubuntu? by vitormhenrique on Tue, 2019-10-22 16:00 |
7 |
by JackGunnarsson Mon, 2023-10-02 13:20 |
VESC Tool | |
|
CAN bus protocol upgrade thoughts by Pimousse on Fri, 2020-03-20 15:37 |
7 |
by renaudbarbier Sat, 2024-04-27 07:53 |
VESC Development and Beta Testing | |
|
PID Speed Control not working in ADC mode by a.smith on Mon, 2022-01-17 13:23 |
7 |
by lonelypanda Wed, 2023-11-15 08:40 |
General discussion | |
|
Disable throttle while braking by rl_19 on Sat, 2022-03-19 00:05 |
7 |
by flez1966 Thu, 2024-03-21 09:41 |
VESC Original Hardware | |
|
Breaking Light by vitormhenrique on Wed, 2020-02-12 18:03 |
7 |
by cbecker333 Thu, 2024-08-22 01:21 |
VESC Firmware | |
|
Welcome by frank on Fri, 2017-06-02 16:31 |
7 |
by sebaszz Fri, 2017-06-09 22:36 |
VESC6 Beta | |
|
How does regenerative braking get enough voltage from my motor to charge my battery from ? by cnd on Wed, 2020-09-16 16:54 |
7 |
by flydr2 Mon, 2023-02-27 22:21 |
General discussion | |
|
Sensorless ERPM confusion and cogging in FOC by Addy on Mon, 2018-05-14 22:38 |
7 |
by bayetan Sun, 2023-06-04 17:19 |
General discussion | |
|
latest FW ,but your VESC needs to updated? by eastcoastkiter on Sun, 2019-07-07 16:55 |
7 |
by Rc 44 Sat, 2019-07-13 01:33 |
VESC Firmware | |
|
app config will revert to default @VESC6MKV by HIROKI_NAKANO on Tue, 2022-02-01 06:39 |
7 |
by eguven Sat, 2024-06-29 20:47 |
General discussion | |
|
Switch two Motor Profiles/Modes (UART) by anli on Thu, 2018-08-16 19:02 |
7 |
by basti30 Sun, 2018-09-30 19:55 |
General discussion |
Pages
