You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Motor clicking and not spinning after setup wizard by dfelz on Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
VESC Tool | |
|
THERE IS NO ONE IN HERE HAHA by zip on Sun, 2024-06-30 12:41 |
by zip Sun, 2024-06-30 12:41 |
VESC Tool | ||
|
Bimodal Ld-Lq Saliency on T Motor AT4130 by ohceejay on Wed, 2026-04-15 18:30 |
by ohceejay Wed, 2026-04-15 18:30 |
VESC Tool | ||
|
Delay on reverse function on electric boat by FreddyForLaunch on Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
VESC Tool | |
|
FOC detection needs load? by tuloski on Thu, 2018-09-13 10:19 |
1 |
by TechAUmNu Thu, 2018-09-13 12:26 |
VESC Tool | |
|
PPM Pulselength mapping by Shaftdriver on Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
VESC Tool | |
|
Constant Serial port errors by SteveBrantley on Tue, 2025-01-21 23:13 |
by SteveBrantley Tue, 2025-01-21 23:13 |
VESC Tool | ||
|
VESC Tool 3.0 can't run input wizzard by thib on Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
VESC Tool | |
|
Updating App and info xml failed by Pimousse on Tue, 2018-01-30 21:06 |
by Pimousse Tue, 2018-01-30 21:06 |
VESC Tool | ||
|
VESC100/250 - motor current setting ignored? by tobiokanobi on Mon, 2022-05-02 13:27 |
3 |
by frank Tue, 2022-05-03 20:54 |
VESC Tool | |
|
Is there a complete documentation for the communication protocol between the vesc tool and the board? by aishangmu on Tue, 2018-12-25 09:00 |
2 |
by Caustic_Zinc Fri, 2019-02-08 19:27 |
VESC Tool | |
|
Bug Report CONNECTION ISSUES 6.06 by andredi on Mon, 2025-09-01 17:36 |
by andredi Mon, 2025-09-01 17:36 |
VESC Tool | ||
|
VESC Tool Crashing on connection (on Macbook version) by svelte.ca on Thu, 2025-07-31 00:00 |
2 |
by etavav Thu, 2025-09-18 17:19 |
VESC Tool | |
|
How to determine motor size in wizard, hub motors ? by Photolad61 on Mon, 2019-03-25 19:43 |
1 |
by Kent Tabor Fri, 2020-10-23 22:29 |
VESC Tool | |
|
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 on Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
VESC Tool | |
|
VESC Partially off Screen by jr226 on Sun, 2023-12-17 20:59 |
1 |
by NOAI Sat, 2024-02-10 14:48 |
VESC Tool | |
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
Motor setup help please by TrevM on Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
VESC Tool | |
|
ADC and arrow input dont work by stefann on Wed, 2019-10-09 18:51 |
by stefann Wed, 2019-10-09 20:04 |
VESC Tool | ||
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes on Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
VESC Tool |
Pages
