You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
FAULT CODE UNBALANCED CURRENT by NOAI on Mon, 2024-03-25 09:30 |
by NOAI Mon, 2024-03-25 09:30 |
Third Party Hardware | ||
|
VESC 6 Edu and encoder AMT203-V by Qubi_24 on Thu, 2025-08-14 13:31 |
by Qubi_24 Thu, 2025-08-14 14:47 |
VESC Tool | ||
|
Auxiliary Output Mode pin# by garyp on Sat, 2020-08-22 18:17 |
by garyp Sat, 2020-08-22 18:17 |
General discussion | ||
|
Cruise function already implemented? by sam.vanratt on Wed, 2019-01-02 17:05 |
by sam.vanratt Wed, 2019-01-02 17:20 |
General discussion | ||
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ on Mon, 2019-09-16 19:36 |
by MaddiQ Mon, 2019-09-16 19:36 |
VESC Firmware | ||
|
(CLOSED)Custom FW based on beta "could not deserialize" by pe on Wed, 2021-12-15 11:48 |
by pe Wed, 2021-12-15 15:18 |
VESC Development and Beta Testing | ||
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion | ||
|
HFI with PPM in Duty Cycle by DaganWal on Fri, 2024-08-30 00:30 |
by DaganWal Fri, 2024-08-30 00:30 |
General discussion | ||
|
-solved- by KittenDude on Sat, 2020-11-28 06:30 |
by KittenDude Sun, 2020-11-29 19:27 |
General discussion | ||
|
Issue with Vesc Tool: MPU6050 IMU Not Detected After Power Cycling by Lennart Duijn on Thu, 2023-06-01 21:54 |
by Lennart Duijn Fri, 2023-06-02 09:03 |
VESC Tool | ||
|
Firmware Update = Quiet Motor? by worldmaverik on Sun, 2020-04-19 21:45 |
by worldmaverik Sun, 2020-04-19 21:45 |
General discussion | ||
|
Unity HFI but I can only configure one motor by ZQuimson on Mon, 2021-06-07 20:02 |
by ZQuimson Mon, 2021-06-07 20:02 |
General discussion | ||
|
GT2 Remote to Vesc connection issue by tom.embke on Tue, 2018-05-01 14:41 |
by tom.embke Tue, 2018-05-01 14:41 |
General discussion | ||
|
Video Live Streams of a dual drive based on stm32f429 by mkschreder on Sat, 2019-03-30 16:25 |
by mkschreder Sat, 2019-03-30 16:28 |
Third Party Hardware | ||
|
ADC input protection proposal by arestechfinland on Mon, 2020-07-06 19:41 |
by arestechfinland Mon, 2020-07-06 19:41 |
General discussion | ||
|
How do I disable brake? by moo10032 on Tue, 2021-02-23 08:09 |
by moo10032 Tue, 2021-02-23 08:10 |
VESC Tool | ||
|
low speed / high friction startup, max torque by schnedan on Mon, 2025-02-24 10:18 |
by schnedan Mon, 2025-02-24 10:19 |
General discussion | ||
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse on Fri, 2022-06-03 08:13 |
by notahorse Fri, 2022-06-03 08:13 |
General discussion | ||
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 on Thu, 2017-10-05 17:21 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
VESC Firmware | ||
|
Error on log-file recording: Could not get Positioning Working by hpb66 on Mon, 2022-05-23 08:23 |
by hpb66 Mon, 2022-05-23 08:23 |
VESC Tool |
Pages
