You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r on Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
VESC Tool | |
|
USB Unable to connect by Bazeljet on Thu, 2019-10-10 06:02 |
5 |
by portnawake Mon, 2019-10-28 21:42 |
General discussion | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
AMT 102 Encoder not working properly with VESC by DerpRush on Thu, 2019-07-25 11:32 |
5 |
by ripperpc Wed, 2022-04-06 21:36 |
General discussion | |
|
Calculation of Current and Voltage by Christian on Tue, 2017-12-12 10:12 |
5 |
by Roger Wolff Sun, 2018-01-07 15:41 |
VESC Firmware | |
|
VESC for Multirotor / Betaflight flight controller SBUS input by Autek-Xracing on Sun, 2017-11-26 01:39 |
5 |
by jordanlow Sun, 2019-11-24 13:30 |
VESC Firmware | |
|
Pulling fault codes without USB by shaman on Fri, 2019-10-18 15:13 |
5 |
by shaman Sun, 2019-10-20 22:54 |
General discussion | |
|
VESC on OSX? by liamcaff on Fri, 2018-09-21 14:16 |
5 |
by Jfriesen Mon, 2021-10-25 16:18 |
The VESC-Project | |
|
On MOSFET choice and replacement by DarioP on Wed, 2020-09-30 14:11 |
5 |
by TheFallen Fri, 2020-10-02 10:57 |
General discussion | |
|
Updated firmware, now can't setup VESC...wth? by kchxaz on Fri, 2019-06-21 18:02 |
5 |
by Gatze Sun, 2019-08-04 09:09 |
VESC Firmware | |
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi on Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
VESC Tool | |
|
Help calibrating a hub motor by Tin_Man_0 on Thu, 2019-12-26 01:17 |
5 |
by vadicus Tue, 2020-01-07 00:48 |
General discussion | |
|
Bad detection problem by baron456 on Fri, 2018-06-29 17:56 |
5 |
by frank Fri, 2018-07-13 14:41 |
VESC Tool | |
|
Current In vs Current Motor by hacksmithCabe on Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
VESC Tool | |
|
I can't get my fresc to work I think all the leds are lighting up but when I pull the trigger on the remote nothing happens by pdxcjc on Fri, 2022-03-11 17:46 |
5 |
by Gatze Mon, 2022-05-09 17:03 |
Third Party Hardware | |
|
HW4.12 with FW 3.27, FOC OK, BLDC problems. by ThierryGTLTS on Thu, 2017-09-07 11:14 |
5 |
by ThierryGTLTS Sat, 2017-09-16 18:45 |
VESC Tool | |
|
PAS function by sam.vanratt on Sat, 2018-11-24 14:53 |
5 |
by Oldbike2011 Mon, 2023-01-30 06:05 |
General discussion | |
|
VESC as a 3 phase inverter to power a grid model by pf26 on Tue, 2019-03-19 20:54 |
5 |
by shaman Fri, 2019-10-18 15:06 |
General discussion | |
|
AC Induction Motor Control Support by shaman on Fri, 2019-04-12 17:50 |
5 |
by Erealind Tue, 2021-06-22 01:06 |
Feature Requests | |
|
Small motor with vesc? by spacemango on Mon, 2020-06-08 21:14 |
5 |
by spacemango Tue, 2020-06-16 15:30 |
General discussion |
Pages
