You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Position control with Hall and A/B encoder by jo.rauchfuss on Tue, 2019-12-17 04:12 |
4 |
by frank Thu, 2019-12-19 21:09 |
General discussion | |
|
VESC settings for large scooter motor by trimen on Tue, 2020-07-14 22:15 |
7 |
by Chris Barth Thu, 2022-07-07 15:51 |
General discussion | |
|
large hub motors by Frankey on Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
General discussion | |
|
ADC1 reads incorrect values by dsuresh on Tue, 2021-02-23 00:51 |
2 |
by dsuresh Mon, 2021-03-01 20:37 |
General discussion | |
|
VESC 100/250 by PBR-Automatyka on Tue, 2021-11-02 12:17 |
1 |
by PBR-Automatyka Tue, 2021-11-02 12:18 |
General discussion | |
|
Vesc - UAVCAN - Pixhawk by dbau on Tue, 2022-02-01 07:43 |
1 |
by dbau Tue, 2022-02-01 07:57 |
General discussion | |
|
Noise between VESC and microcontroller by onsokumaru on Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
General discussion | |
|
Current sensor and commanded current by galp on Fri, 2019-02-22 23:08 |
by galp Fri, 2019-02-22 23:08 |
General discussion | ||
|
what is the best vesc For long-term sea observation by jhgjg on Thu, 2022-09-22 12:12 |
5 |
by frank Mon, 2022-09-26 15:44 |
General discussion | |
|
Current Control issue VESC4 by yosoufe on Tue, 2018-03-20 09:28 |
5 |
by itchavenag Fri, 2019-09-13 12:06 |
General discussion | |
|
Struggling in startup BLDC in sensorless mode by dangminhducnbk on Fri, 2019-02-15 03:42 |
2 |
by dangminhducnbk Sun, 2019-02-17 12:48 |
General discussion | |
|
Pole Pairs by donrecardo on Fri, 2020-06-05 10:24 |
3 |
by TheFallen Mon, 2020-06-08 16:23 |
General discussion | |
|
Current limit problem by albheim on Fri, 2022-09-09 10:34 |
2 |
by albheim Fri, 2022-09-09 13:24 |
General discussion | |
|
FSESC 4.2 Firmware Resetting by Pranay on Fri, 2021-08-27 12:18 |
1 |
by TechAUmNu Fri, 2021-08-27 17:20 |
General discussion | |
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion | ||
|
Donations to Benjamin by Johnvoss on Mon, 2021-08-16 05:13 |
4 |
by Johnvoss Thu, 2021-08-19 03:14 |
General discussion | |
|
FOC and very low speeds by verbeek on Mon, 2018-07-09 16:17 |
10 |
by moose09876 Wed, 2022-08-24 20:05 |
General discussion | |
|
Power switch on VESC 6 MK III by hans_maier on Mon, 2020-01-20 23:35 |
13 |
by frank Sat, 2020-12-12 18:01 |
General discussion | |
|
My VESC TOOL did not have "balance" by Elijah K on Wed, 2020-08-12 07:52 |
by Elijah K Wed, 2020-08-12 07:53 |
General discussion | ||
|
Problem with regenerative breaking by ligi on Sat, 2022-04-02 15:08 |
3 |
by frank Sun, 2022-04-03 12:31 |
General discussion |
Pages
