You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Duty Cycle Mode - limited ZERO RPM duty cycle by maheshK on Mon, 2021-11-29 11:24 |
2 |
by frank Tue, 2021-11-30 07:46 |
VESC Tool | |
|
Communication over UART or CAN by JCLNEIL on Wed, 2023-12-13 14:36 |
by JCLNEIL Wed, 2023-12-13 14:36 |
VESC Tool | ||
|
Serial port error when Encoder detection is complete by VirtB on Wed, 2018-08-29 03:03 |
3 |
by VirtB Sun, 2018-09-02 03:33 |
VESC Tool | |
|
ERPM, the RPM on the motor does not change by hopeingod on Fri, 2024-05-10 11:15 |
6 |
by hopeingod Mon, 2024-05-13 20:45 |
VESC Tool | |
|
Bug found in VESC tool 6.05 related to VESC BMS by f.damien12 on Wed, 2025-04-09 17:11 |
by f.damien12 Wed, 2025-04-09 17:13 |
VESC Tool | ||
|
Sailboat regen by flydr2 on Wed, 2023-04-12 20:10 |
1 |
by vadicus Wed, 2023-05-10 20:06 |
VESC Tool | |
|
USB-serial_no ports show up at all by Josiah Eberharter on Tue, 2024-07-23 05:45 |
by Josiah Eberharter Tue, 2024-07-23 05:45 |
VESC Tool | ||
|
PPM throttle detected in Vesc Tool but has no effect on motor by maxim1977 on Sat, 2025-07-26 06:03 |
1 |
by ftpkmarcelo Sun, 2025-08-10 06:07 |
VESC Tool | |
|
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool | ||
|
Motor clicking and not spinning after setup wizard by dfelz on Fri, 2020-04-03 03:51 |
6 |
by brian adilman Wed, 2022-01-26 13:36 |
VESC Tool | |
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
Motors wont turn independently by huffauden19 on Mon, 2020-11-30 06:24 |
by huffauden19 Mon, 2020-11-30 06:24 |
VESC Tool | ||
|
Cruise Control button no longer working by Jobbel on Tue, 2017-09-05 01:10 |
1 |
by Jobbel Sun, 2022-09-25 16:36 |
VESC Tool | |
|
FOC for BDC? by SlimSh8y on Thu, 2018-07-12 23:05 |
11 |
by JanneHooo Fri, 2023-10-13 18:20 |
VESC Tool | |
|
Detection failed. Reason: -11 by Eco Delsbo on Fri, 2019-05-03 12:01 |
10 |
by Gatze Wed, 2020-03-18 22:04 |
VESC Tool | |
|
Writing to slave vesc sometimes cause loss of can bus by meashman on Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
VESC Tool | |
|
Dual VESC and One Motor Stops Spinning by f0n on Tue, 2025-02-11 02:22 |
3 |
by DavidjohnNeff Wed, 2025-02-12 05:57 |
VESC Tool | |
|
VESC Tool 6.02 by JWilson on Thu, 2024-03-21 18:30 |
1 |
by electricfox Thu, 2024-03-21 23:15 |
VESC Tool | |
|
single VESC 6+ controlled by CAN-bus by vinci on Fri, 2021-07-09 15:42 |
1 |
by yuri12 Wed, 2022-02-09 17:23 |
VESC Tool | |
|
Vesc mAh reading by th0masrtg on Tue, 2020-09-29 08:48 |
by th0masrtg Wed, 2020-09-30 19:58 |
VESC Tool |
Pages
