You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
PAS sensor for pedelec and speed pedelec by th0masrtg on Sun, 2020-04-26 08:55 |
4 |
by th0masrtg Thu, 2020-10-29 07:38 |
Feature Requests | |
|
Too little torque. by Roger Wolff on Thu, 2018-05-10 18:11 |
4 |
by Roger Wolff Mon, 2018-05-14 19:30 |
General discussion | |
|
Setting up low KV brushless motor? by Trent on Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
General discussion | |
|
Porting to a newer STM32 by TechAUmNu on Wed, 2020-09-16 12:38 |
4 |
by STEPHY AKKARA Thu, 2022-04-14 07:57 |
VESC Firmware | |
|
Driver explosion by fer-bo on Mon, 2021-07-05 11:48 |
4 |
by fer-bo Wed, 2021-07-07 14:50 |
General discussion | |
|
Need Help with HI200-C from Maker X by Moritz@liebler.net on Tue, 2021-01-12 14:44 |
4 |
by Oded Mazor Thu, 2022-03-24 12:05 |
Third Party Hardware | |
|
Pitting VESC Six EDU against a Castle Creations ESC - the Castle is winning? by jschall on Fri, 2023-07-14 18:58 |
4 |
by drummerboy5408 Thu, 2023-11-02 23:24 |
General discussion | |
|
Using reverse with a spare channel by spork on Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
General discussion | |
|
Been at it for like 14 hours... HALP by mnchvgs79 on Wed, 2021-03-03 22:03 |
4 |
by TheFallen Sun, 2021-03-07 15:25 |
VESC Tool | |
|
Overvoltage Error during setup by arranto12 on Mon, 2021-11-08 23:22 |
4 |
by electricfox Tue, 2025-02-04 19:28 |
General discussion | |
|
VESC 75/300 with sin/cos encoder by sajjen on Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
VESC Original Hardware | |
|
C Type USB and Power Delivery 3.1 by Rarikao on Fri, 2023-04-21 08:51 |
4 |
by vadicus Fri, 2023-04-28 05:30 |
Feature Requests | |
|
BIG Flash/Spark!!!!! New 100v/250a :-( by Fpvlee on Thu, 2021-05-13 03:17 |
4 |
by Fpvlee Tue, 2021-05-25 00:12 |
General discussion | |
|
Bafang hub motor setup by Kent Tabor on Fri, 2020-10-16 03:48 |
4 |
by Racing2Learn Sun, 2024-05-05 18:31 |
VESC Tool | |
|
Merry Christmas! by frank on Fri, 2017-12-22 14:31 |
4 |
by ThierryGTLTS Sun, 2017-12-24 14:34 |
General discussion | |
|
FW=ADC1, REV=ADC2 by ProgramThyself on Sat, 2020-08-01 23:30 |
4 |
by ProgramThyself Mon, 2020-08-03 03:56 |
General discussion | |
|
Available connectors by nopf on Wed, 2024-09-18 09:33 |
4 |
by tobiokanobi Sun, 2024-10-20 17:38 |
VESC Original Hardware | |
|
Set RPM - reverse direction over CAN-Bus by 65273 on Tue, 2022-03-29 14:49 |
4 |
by 65273 Fri, 2022-04-01 15:53 |
General discussion | |
|
Connect vesc tool with ANT BMS by Vdca on Sun, 2024-01-14 23:15 |
4 |
by Timo Wedel Sat, 2024-07-27 14:41 |
VESC Tool | |
|
Reverse button configuration by ElectroToshka on Thu, 2022-06-23 11:09 |
4 |
by frank Fri, 2022-06-24 10:42 |
Third Party Hardware |
Pages
