You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Variable regen braking by Gsorter on Thu, 2024-07-11 00:04 |
by Gsorter Thu, 2024-07-11 00:04 |
General discussion | ||
|
VCC-GND short by caliber interconnect on Sat, 2022-02-26 13:10 |
4 |
by caliber interconnect Tue, 2022-03-01 10:42 |
VESC Original Hardware | |
|
VEC 4.20 50A current limitations by Jean-Michel RAVON on Thu, 2021-03-18 14:16 |
by Jean-Michel RAVON Thu, 2021-03-18 14:16 |
General discussion | ||
|
VECT Tool freezes after uploading lisp script by realphanta on Sun, 2025-07-27 17:05 |
2 |
by realphanta Thu, 2025-07-31 11:24 |
VESC Tool | |
|
Vedder forums or Vesc forums? by Eric on Wed, 2017-09-13 14:39 |
2 |
by frank Mon, 2017-09-18 10:12 |
General discussion | |
|
Version 0.84, some problems with ADC, see 2nd post please! by ThierryGTLTS on Sun, 2017-10-29 14:11 |
3 |
by ThierryGTLTS Fri, 2017-11-03 16:56 |
VESC Tool | |
|
Version 2.03 won't open by marialoise on Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
VESC Tool | |
|
Version 3.01 destroyed version 2.06 too by Knaubel on Sun, 2022-05-15 21:23 |
6 |
by Knaubel Wed, 2022-05-18 16:16 |
VESC Tool | |
|
Version 6+ make arm_sdk_install failing by trtr6842 on Mon, 2024-07-01 02:03 |
1 |
by onid Sat, 2024-07-13 11:21 |
VESC Firmware | |
|
version of the vesc tool by aysubscriber@ic... on Tue, 2017-10-03 07:53 |
4 |
by aysubscriber@ic... Fri, 2017-10-13 03:47 |
General discussion | |
|
version of Vesc Tool for Flipsky 6.6 by Robert Adkins on Sun, 2019-09-29 18:13 |
3 |
by frank Wed, 2019-10-23 09:35 |
VESC Tool | |
|
Very Large hub motor detection (QSMOTOR 3000W hub) by shaman on Thu, 2020-02-20 01:26 |
5 |
by fart Wed, 2024-04-03 10:43 |
General discussion | |
|
Very low Flux Linkage calulation FOC,General Tab - 0.0xx mWb by kjjajsdASHD on Sun, 2025-02-02 13:59 |
by kjjajsdASHD Sun, 2025-02-02 13:59 |
VESC Tool | ||
|
Very weird short by dusi007 on Sat, 2022-03-19 11:36 |
1 |
by skyline1970 Mon, 2022-03-28 16:29 |
Third Party Hardware | |
|
VESC "underpowered" vs Kunteng Controller experience by andyw2005 on Thu, 2021-10-21 23:54 |
1 |
by Elwin Fri, 2021-10-22 11:39 |
General discussion | |
|
VESC & CAN Bus Communication to another MCU (NOT VESC) by Jack_Li on Thu, 2019-07-11 04:08 |
5 |
by David_1 Thu, 2022-08-11 22:08 |
VESC Firmware | |
|
VESC - custom board by st0r on Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
General discussion | |
|
VESC - FAULT_CODE_DRV : motor no more spinning by piepolitb on Sat, 2018-05-19 12:27 |
4 |
by seif Wed, 2020-03-11 20:12 |
General discussion | |
|
VESC - HIL / DRV8301 SPI - Problems? by mm_iem on Tue, 2022-08-09 12:34 |
1 |
by skyline1970 Thu, 2022-11-24 20:54 |
VESC Firmware | |
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion |
Pages
