You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Maytech 200A does not work in FOC, will a A200S work better? by doom on Wed, 2019-08-07 20:40 |
1 |
by TechAUmNu Fri, 2019-08-09 21:01 |
Third Party Hardware | |
|
what do you guys think about this "curr_samp_volt "? by jem on Thu, 2019-08-08 14:45 |
by jem Thu, 2019-08-08 14:45 |
VESC Firmware | ||
|
VESC4 phase shunt by Rico on Tue, 2019-05-21 16:09 |
3 |
by svs Thu, 2019-08-08 08:41 |
VESC Firmware | |
|
UART communication by EthB on Wed, 2017-09-06 19:13 |
19 |
by stefcux Thu, 2019-08-08 03:16 |
General discussion | |
|
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
|
VESC UART Espruino by Gpole on Mon, 2019-05-20 12:25 |
2 |
by hughlloyd Wed, 2019-08-07 06:22 |
VESC Firmware | |
|
"Throttle" help by benha on Wed, 2019-08-07 05:58 |
by benha Wed, 2019-08-07 05:58 |
General discussion | ||
|
"bad detection result received" impossible to achieved motor detection ! by titimomotete on Wed, 2019-03-20 17:21 |
2 |
by doom Mon, 2019-08-05 10:52 |
VESC Tool | |
|
VESC PID not working by vulkan66 on Tue, 2019-07-30 10:29 |
2 |
by vulkan66 Sun, 2019-08-04 17:13 |
General discussion | |
|
Updated firmware, now can't setup VESC...wth? by kchxaz on Fri, 2019-06-21 18:02 |
5 |
by Gatze Sun, 2019-08-04 09:09 |
VESC Firmware | |
|
Help setting up dual vesc via CANBUS by Jaystro16 on Sun, 2019-08-04 01:39 |
by Jaystro16 Sun, 2019-08-04 01:39 |
VESC Firmware | ||
|
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
|
VESC Firmware update not working by timhermanson94 on Wed, 2019-07-31 18:42 |
1 |
by skyline1970 Fri, 2019-08-02 15:22 |
VESC Firmware | |
|
VESC 4.12 firmware 3.38 flash back to firmware 2.18 by Arm007 on Thu, 2019-04-11 08:30 |
3 |
by skyline1970 Fri, 2019-08-02 15:15 |
VESC Firmware | |
|
Controlling VESC with arduino - by vulkan66 on Thu, 2019-07-11 11:51 |
3 |
by vulkan66 Thu, 2019-08-01 21:34 |
General discussion | |
|
Hooking up two or more motor drivers to the same MCU by darkclaude on Thu, 2019-06-20 10:02 |
2 |
by skyline1970 Wed, 2019-07-31 13:53 |
VESC Original Hardware | |
|
Hooking up two or more motor drivers to the same MCU by darkclaude on Thu, 2019-06-20 10:02 |
4 |
by skyline1970 Wed, 2019-07-31 13:53 |
Third Party Hardware | |
|
VESC Hardware by eschroff on Thu, 2019-07-25 02:38 |
1 |
by skyline1970 Wed, 2019-07-31 13:35 |
VESC Original Hardware | |
|
Is the Diy pcb version still working? by jon218white on Sat, 2019-07-27 00:58 |
1 |
by skyline1970 Wed, 2019-07-31 13:33 |
General discussion | |
|
VESC CAN_STATUS_1_2_3_4 explained (RPi) by kimpet on Mon, 2019-05-13 12:51 |
3 |
by Jack_Li Tue, 2019-07-30 14:01 |
General discussion |
Pages
