You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Cannot reach max speed of BLDC motor by rousha42 on Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
General discussion | |
|
Measure resistance with IGBTs by mtzm on Wed, 2018-04-04 14:46 |
4 |
by jaredreese Thu, 2019-10-03 11:41 |
VESC Firmware | |
|
Wand speed display incorrect - Solved by hans_maier on Sat, 2019-09-14 15:16 |
4 |
by hans_maier Wed, 2019-09-18 22:31 |
General discussion | |
|
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
VESC Tool | |
|
Motor spins only with outside help by asaf123098 on Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
Third Party Hardware | |
|
Updated VESC 6 schematic request by ma-j-sterelektron on Mon, 2019-03-25 08:43 |
4 |
by jejaj25773 Fri, 2024-07-26 02:29 |
General discussion | |
|
Burned my VESC 6 MKV. Wrong polarity by okhsunrog on Thu, 2022-04-07 01:44 |
4 |
by frank Thu, 2022-04-07 10:27 |
General discussion | |
|
How to tell what HW version I have and set conf_general.h by jmachuca77 on Fri, 2021-02-19 19:21 |
4 |
by danilolattaro Mon, 2021-04-12 19:38 |
VESC Development and Beta Testing | |
|
Feature request: Raw hall data. by Roger Wolff on Mon, 2018-06-11 15:49 |
4 |
by blubbi321 Tue, 2022-03-29 16:32 |
VESC Tool | |
|
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
|
Pole Pairs by donrecardo on Fri, 2020-06-05 10:24 |
4 |
by Bgbalz75 Fri, 2025-05-16 13:01 |
General discussion | |
|
How to increase startup torque? by Enak on Fri, 2017-09-08 01:14 |
4 |
by vadicus Tue, 2021-02-23 19:44 |
VESC Tool | |
|
Donations to Benjamin by Johnvoss on Mon, 2021-08-16 05:13 |
4 |
by Johnvoss Thu, 2021-08-19 03:14 |
General discussion | |
|
Is the Vesc 5 mkIII capable of 13s li-Ion (fully charged 54,6V) by Pelle on Sun, 2020-04-12 12:09 |
4 |
by danilolattaro Thu, 2021-04-22 14:50 |
General discussion | |
|
VESC amplifier ? by Markula on Fri, 2020-11-13 14:52 |
4 |
by s0313045 Mon, 2020-11-16 23:50 |
General discussion | |
|
Firware 5.2 by julitosanse on Mon, 2021-01-25 15:04 |
4 |
by firemaxx Thu, 2024-07-18 08:46 |
VESC Firmware | |
|
How to interpret the result of "last_adc_duration" (terminal command)? by RSR on Fri, 2017-09-08 15:55 |
4 |
by RSR Sat, 2017-09-09 18:38 |
VESC Firmware | |
|
Charge wires by Phill Dixon on Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
General discussion | |
|
VESC 100/250 by XBO on Tue, 2021-09-07 19:25 |
4 |
by frank Mon, 2021-09-20 14:01 |
General discussion | |
|
FSESC 6.6 dual short on 3.3v on 1 side by vic1234 on Thu, 2022-02-17 22:33 |
4 |
by vic1234 Fri, 2022-02-18 17:52 |
VESC Original Hardware |
Pages
