You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Difference between Brake Current, Full Brake etc by wdaehn on Wed, 2018-02-21 15:32 |
4 |
by rodread Sat, 2018-03-03 10:45 |
General discussion | |
|
controlling 2 motors for two directions each by ori harush on Mon, 2022-06-06 07:17 |
4 |
by Indy8976 Tue, 2022-06-21 13:36 |
General discussion | |
|
how to download v5.03 firmware? by barncat08 on Wed, 2022-01-26 18:35 |
4 |
by Gatze Sat, 2022-04-23 11:48 |
VESC Firmware | |
|
FOC observer error. by Roger Wolff on Thu, 2018-06-07 13:43 |
4 |
by district9prawn Wed, 2018-12-12 23:44 |
General discussion | |
|
Switching frequency data by petertaylor on Thu, 2018-11-08 00:53 |
4 |
by petertaylor Tue, 2018-12-25 20:28 |
VESC Firmware | |
|
foc observer/phase loosing track at phase current limit by Teslafly on Tue, 2018-07-24 18:46 |
4 |
by cir7 Thu, 2022-07-14 17:07 |
General discussion | |
|
Stall torque in sensorless mode by cromoly on Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
General discussion | |
|
Save state data on vesc? by NuRxG on Thu, 2020-04-09 06:44 |
4 |
by ProgramThyself Sat, 2020-09-12 08:42 |
VESC Development and Beta Testing | |
|
Getting Started / Prototyping Help by harrym on Wed, 2020-04-01 17:56 |
4 |
by javmarina Sat, 2020-05-09 17:35 |
General discussion | |
|
E vehicle setup by jordanlow on Wed, 2019-03-20 10:33 |
4 |
by jordanlow Wed, 2019-03-20 16:18 |
General discussion | |
|
VESC75/300 - Does your IMU work? by Gerhard on Mon, 2021-02-08 00:15 |
4 |
by Gerhard Thu, 2021-02-25 17:39 |
VESC Original Hardware | |
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons on Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
VESC Original Hardware | |
|
lispBM on VESC for special algorithm by Fusion on Fri, 2024-10-25 11:34 |
4 |
by Fusion Sat, 2024-10-26 17:00 |
General discussion | |
|
step/dir by blueflower on Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
General discussion | |
|
Current In vs Current Motor by hacksmithCabe on Thu, 2021-09-30 21:59 |
5 |
by y-hasebe Mon, 2021-12-13 15:17 |
VESC Tool | |
|
I can't get my fresc to work I think all the leds are lighting up but when I pull the trigger on the remote nothing happens by pdxcjc on Fri, 2022-03-11 17:46 |
5 |
by Gatze Mon, 2022-05-09 17:03 |
Third Party Hardware | |
|
VESC & CAN Bus Communication to another MCU (NOT VESC) by Jack_Li on Thu, 2019-07-11 04:08 |
5 |
by David_1 Thu, 2022-08-11 22:08 |
VESC Firmware | |
|
Dual motor setup over CAN with UART by Pawel on Sun, 2018-06-17 11:50 |
5 |
by alex63610 Fri, 2019-12-27 14:27 |
VESC Firmware | |
|
Rough transition to sensorless under load by vadicus on Sat, 2020-07-18 07:10 |
5 |
by vadicus Wed, 2020-08-05 20:10 |
General discussion | |
|
experiment tab rpm ramp up and dual separate motor control by tobiokanobi on Thu, 2022-04-14 20:20 |
5 |
by tobiokanobi Tue, 2022-04-26 15:32 |
VESC Tool |
Pages
