You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
PWM encoder support by Ieton2hahw on Fri, 2021-06-18 05:47 |
4 |
by electricfox Tue, 2025-04-08 10:54 |
Feature Requests | |
|
FOC VESC for QS Motor 205 50H 3000w by karlisakis on Mon, 2021-06-07 21:29 |
4 |
by vadicus Mon, 2021-10-25 19:39 |
General discussion | |
|
Rolling down-hill faster than my board's electric top speed by koralle on Tue, 2018-05-01 21:18 |
4 |
by koralle Sun, 2018-05-06 18:25 |
General discussion | |
|
Two phase modulation by jguy on Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
General discussion | |
|
Dual VESC sync problem by Svenska Svenson on Wed, 2017-10-18 18:56 |
4 |
by Svenska Svenson Sat, 2017-10-28 13:47 |
VESC Original Hardware | |
|
One trasmitter two receivers by vikiki on Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
VESC Tool | |
|
Back EMF or motor voltage back to the supply by bdesvaux on Tue, 2022-09-27 09:22 |
4 |
by bdesvaux Wed, 2022-09-28 15:52 |
General discussion | |
|
Setting up low KV brushless motor? by Trent on Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
General discussion | |
|
Porting to a newer STM32 by TechAUmNu on Wed, 2020-09-16 12:38 |
4 |
by STEPHY AKKARA Thu, 2022-04-14 07:57 |
VESC Firmware | |
|
Anti cogging, suppressing torque ripple? by Alistair Goodman on Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
General discussion | |
|
Kill switch feature through adc input by Heddan99 on Sun, 2021-03-07 12:54 |
4 |
by frank Thu, 2021-06-10 14:18 |
Feature Requests | |
|
Cannot reach max speed of BLDC motor by rousha42 on Wed, 2021-11-03 20:23 |
4 |
by frank Tue, 2021-11-09 09:46 |
General discussion | |
|
Hall Sensors Not Detected by leymane on Fri, 2023-08-18 17:12 |
4 |
by Ben26 Mon, 2024-10-21 22:45 |
General discussion | |
|
Need Help with HI200-C from Maker X by Moritz@liebler.net on Tue, 2021-01-12 14:44 |
4 |
by Oded Mazor Thu, 2022-03-24 12:05 |
Third Party Hardware | |
|
CanOpen by maxmertins on Mon, 2023-01-30 17:10 |
4 |
by maxmertins Wed, 2023-02-01 17:24 |
General discussion | |
|
Using reverse with a spare channel by spork on Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
General discussion | |
|
Delay on reverse function on electric boat by FreddyForLaunch on Tue, 2021-06-01 12:31 |
4 |
by electricfox Wed, 2022-08-17 20:59 |
VESC Tool | |
|
VESC 75/300 with sin/cos encoder by sajjen on Tue, 2019-11-12 16:16 |
4 |
by marcos_ Sun, 2020-01-19 22:48 |
VESC Original Hardware | |
|
VESC Tool 3.0 can't run input wizzard by thib on Mon, 2021-09-27 00:58 |
4 |
by frank Fri, 2021-10-29 10:07 |
VESC Tool | |
|
half speed on FOC vs BLDC by ever.summer on Tue, 2019-05-28 00:04 |
4 |
by ever.summer Tue, 2019-05-28 04:34 |
General discussion |
Pages
