You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Does VESC reduce/disable regen braking based on battery voltage? by rorosaurus on Tue, 2020-08-11 23:20 |
11 |
by J_W97 Mon, 2022-03-14 14:43 |
General discussion | |
|
Does Trampa BMS work with multiple VESCs? by kylerlaird on Sun, 2025-04-20 03:57 |
2 |
by kylerlaird Sun, 2025-04-20 15:38 |
VESC Original Hardware | |
|
Does the VESC allow for Bidirectional Control? by DTSB on Thu, 2020-11-19 18:28 |
2 |
by Open UAS Sat, 2020-11-21 23:22 |
General discussion | |
|
Does the code right by jennyxcy2008 on Mon, 2019-01-28 02:57 |
7 |
by jennyxcy2008 Tue, 2019-01-29 04:52 |
VESC Firmware | |
|
Does the blue tooth adapter from Flipsky now work with Iphone? by Don124 on Thu, 2022-06-23 07:50 |
1 |
by oskkis Wed, 2022-08-17 18:48 |
Third Party Hardware | |
|
Does PLL measure the REAL motor speed by wyk on Mon, 2020-11-23 08:34 |
by wyk Mon, 2020-11-23 08:34 |
General discussion | ||
|
Does PLL measure the REAL motor speed by wyk on Mon, 2020-11-23 08:01 |
by wyk Mon, 2020-11-23 08:01 |
VESC Firmware | ||
|
Does a wireless passive on/off ignition switch that holds its state exist? Need help for my custom electric scooter! by 010203040506070809 on Mon, 2019-09-30 23:59 |
1 |
by Enak Thu, 2019-10-10 03:21 |
General discussion | |
|
Documentation - Input Setup Wizard for multiple VESCs via CAN-Bus, using a PPM signal radio controller by Enak on Sat, 2019-04-13 04:06 |
3 |
by frank Mon, 2021-05-17 07:46 |
The VESC-Project | |
|
Documentation by Cledus on Sat, 2017-12-30 22:23 |
1 |
by Oyta Tue, 2018-01-23 20:35 |
General discussion | |
|
Docker images for vesc build? by dammfine on Thu, 2020-04-23 18:56 |
4 |
by brycej Fri, 2020-07-24 18:06 |
VESC Tool | |
|
Docker container to build custom Firmware - with parent v5.2 by Daniel... on Sat, 2023-09-16 22:00 |
by Daniel... Sat, 2023-09-16 22:00 |
VESC Firmware | ||
|
Do you know how wire simultaneously bluetooth module and 9dof sensor? Bluetooth now connected to TX RX, but it is the same pins by zmei116 on Thu, 2020-08-27 18:02 |
2 |
by thefallen Sun, 2020-08-30 19:33 |
VESC Original Hardware | |
|
Do I need phase voltage sense? by Flepple on Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
General discussion | |
|
Do I need a motor with Hall sensor to use Vesc tool? by greew on Sun, 2020-05-31 06:48 |
by greew Sun, 2020-05-31 06:48 |
General discussion | ||
|
Do All Vescs Suck? by Zeebybaby on Sun, 2024-10-20 20:33 |
by Zeebybaby Sun, 2024-10-20 20:33 |
General discussion | ||
|
DIYElectricSkateboard.com Torque Board Street: DOA by epretorious on Thu, 2022-06-02 17:54 |
3 |
by frank Sat, 2022-06-04 11:50 |
Third Party Hardware | |
|
DIY vesc 75/300 variant power stage problem by motordriver111 on Sat, 2021-03-27 21:44 |
2 |
by vadicus Tue, 2021-04-06 18:50 |
Third Party Hardware | |
|
DIY Vesc 75/300 motor not spinning by motordriver111 on Mon, 2020-08-03 16:39 |
7 |
by motordriver111 Sun, 2020-08-23 08:37 |
VESC6 Beta | |
|
DIY Vesc 6 issues with motor detection by roxes1 on Sun, 2017-11-12 10:15 |
1 |
by roxes1 Sun, 2018-02-11 07:23 |
Third Party Hardware |
Pages
