You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Control singular VESC using CAN-BUS and Arduino by Cam on Wed, 2021-01-06 10:29 |
4 |
by craiggault Wed, 2022-04-27 23:07 |
General discussion | |
|
flipsky 6374 battle hardened with flipsky 6.6 dual vesc by marso on Sun, 2021-08-22 17:35 |
by marso Sun, 2021-08-22 17:36 |
General discussion | ||
|
Battery discharge curve by Madaboutfoiling on Sun, 2023-02-05 08:23 |
1 |
by oangelo Wed, 2023-02-08 00:02 |
General discussion | |
|
Torque Ramp Rate whilst in FOC by J_W97 on Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
General discussion | |
|
status message by riku on Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
General discussion | |
|
Two VESCs with servo-out firmware by _saeed_arabi_ on Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
General discussion | |
|
ADC throttle lock. by Billy_Wiz on Mon, 2022-10-31 00:57 |
1 |
by vadicus Mon, 2022-10-31 19:51 |
General discussion | |
|
VESC Input Using Raspberry Pi and Wiimote by Schizug on Wed, 2019-03-27 04:28 |
3 |
by Nelf Sat, 2020-08-08 01:13 |
General discussion | |
|
E-scooter/bike throttle by Pelle van wijk on Sun, 2019-12-01 17:03 |
7 |
by hummina Wed, 2020-10-14 05:02 |
General discussion | |
|
Differential steering setup by GCTech on Sat, 2020-07-04 17:38 |
3 |
by TheFallen Fri, 2021-06-11 09:36 |
General discussion | |
|
as5047d drift?,Vd voltage -10 by ziumus on Sat, 2021-02-20 20:38 |
3 |
by ziumus Tue, 2021-02-23 22:08 |
General discussion | |
|
noisy braking on vesc4 by lurch on Sat, 2021-10-30 10:30 |
by lurch Sat, 2021-10-30 10:48 |
General discussion | ||
|
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly on Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
General discussion | |
|
Type of motors supported by VESC 6 MKIV by Sami Sahli on Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
General discussion | |
|
Vesc tool not working by faheemift on Sun, 2021-02-14 14:44 |
4 |
by faheemift Wed, 2021-04-14 22:59 |
General discussion | |
|
Controling two motors with Dual FSESC6.6 in two directions by Rafal on Sat, 2021-10-16 13:47 |
1 |
by frank Mon, 2021-10-18 14:43 |
General discussion | |
|
version of the vesc tool by aysubscriber@ic... on Tue, 2017-10-03 07:53 |
4 |
by aysubscriber@ic... Fri, 2017-10-13 03:47 |
General discussion | |
|
position control with gearbox by raess on Tue, 2018-09-25 23:48 |
18 |
by IanG Mon, 2020-03-30 06:44 |
General discussion | |
|
Drive frequency and command rate question by jediengineer on Sun, 2023-03-19 19:07 |
by jediengineer Sun, 2023-03-19 19:08 |
General discussion | ||
|
FAULT_CODE_DRV Motor not spinning by Mightyorc on Sat, 2018-09-15 03:36 |
by Mightyorc Sat, 2018-09-15 03:36 |
General discussion |
Pages
