You are here

Active forum topics

Topic Replies Last postsort ascending Forum
Normal topic VESC 6 MK IV circuit question
by Simmo1337 on Tue, 2022-08-16 23:10
by Simmo1337
Tue, 2022-08-16 23:10
VESC Original Hardware
Hot topic Spam (Page: 1, 2)
by Davideo on Mon, 2017-12-25 20:49
81 by canoeman
Tue, 2022-08-16 15:19
General discussion
Normal topic UART for NRF51822 on "old" nrf pins ?
by CTSchorsch on Fri, 2019-11-29 16:41
6 by hl0dk0
Tue, 2022-08-16 12:46
Feature Requests
Normal topic Small inrunner HFI set-up issue
by anthony_ on Thu, 2022-08-11 13:43
2 by anthony_
Mon, 2022-08-15 13:45
General discussion
Normal topic In FOC mode, MOSFET is often burned out! In BLDC mode, normal!
by return97 on Sat, 2022-07-23 17:31
4 by return97
Sun, 2022-08-14 16:53
General discussion
Normal topic Bafang BBSHD hub motor setup
by csev-tcejorp on Sat, 2022-08-13 14:50
by csev-tcejorp
Sat, 2022-08-13 14:50
Feature Requests
Normal topic VESC TOOL Mobile over OTG
by xvatriusx on Sat, 2022-08-13 04:25
by xvatriusx
Sat, 2022-08-13 04:25
Feature Requests
Normal topic Vesc 100/250 for unsensored brushless motors
by jmurba on Fri, 2022-08-05 12:05
3 by velolac
Fri, 2022-08-12 22:14
General discussion
Hot topic [SOLVED] VESC75/300 Poor Performance when Cold
by canoeman on Tue, 2022-01-25 23:46
25 by canoeman
Fri, 2022-08-12 19:13
VESC Original Hardware
Normal topic VESC & CAN Bus Communication to another MCU (NOT VESC)
by Jack_Li on Thu, 2019-07-11 04:08
5 by David_1
Thu, 2022-08-11 22:08
VESC Firmware
Normal topic Starter motor stoping for no apparent reason
by Bexy on Wed, 2022-08-03 18:07
2 by jiushiwo
Thu, 2022-08-11 08:23
General discussion
Normal topic step/dir
by blueflower on Thu, 2020-01-16 04:15
5 by akkoxe
Mon, 2022-08-08 06:34
General discussion
Normal topic KV command in terminal ( how to determine kv of a motor )
by fessyfoo on Sat, 2020-05-09 21:21
1 by rafeh1
Mon, 2022-08-08 04:31
VESC Tool
Normal topic Flipsky 75100 with Flipsky VX1 remote -- do I have the wiring right? (VESC4 connector)
by SeguinM on Sun, 2022-08-07 15:32
by SeguinM
Sun, 2022-08-07 15:32
Third Party Hardware
Normal topic iq sign reversal at high RPM (was: Duty cycle jumps to maximum when *lowering* current limit)
by vadimz on Thu, 2022-06-23 14:00
4 by vadimz
Sun, 2022-08-07 13:03
VESC Firmware
Normal topic Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM
by PaulMakesThings on Fri, 2022-08-05 11:06
by PaulMakesThings
Fri, 2022-08-05 11:06
General discussion
Normal topic Updated VESC 6 schematic request
by ma-j-sterelektron on Mon, 2019-03-25 08:43
3 by Roby_88
Thu, 2022-08-04 12:43
General discussion
Normal topic temperature compensation make sense?
by alexshen2012 on Thu, 2022-08-04 08:28
1 by alexshen2012
Thu, 2022-08-04 09:17
General discussion
Normal topic FAULT_CODE_UNDER_VOLTAGE
by alexantosh on Mon, 2021-11-29 09:26
9 by heravinluca
Thu, 2022-08-04 04:19
VESC Tool
Normal topic VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current
by liminalsunset on Thu, 2022-08-04 01:44
by liminalsunset
Thu, 2022-08-04 01:44
General discussion

Pages

Subscribe to Active forum topics