You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
VESC 75/300 Configuration problems with Hacker Q80 Motors by electricfox on Thu, 2019-02-28 18:23 |
13 |
by Cherry Tue, 2021-01-12 11:56 |
VESC Tool | |
Vesc-tool TCP Connection by nlabs on Fri, 2017-12-08 02:30 |
1 |
by milesf Fri, 2021-12-10 03:40 |
VESC Tool | |
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies on Wed, 2021-04-28 23:59 |
2 |
by Gloobox Wed, 2022-11-30 18:39 |
VESC Tool | |
VESC Tool Makes my remote unusable by IcecreamSamurai on Mon, 2020-06-15 01:49 |
by IcecreamSamurai Mon, 2020-06-15 01:49 |
VESC Tool | ||
Benchmark regenerative braking by diggis on Fri, 2021-02-19 10:01 |
by diggis Fri, 2021-02-19 10:01 |
VESC Tool | ||
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota on Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
VESC Tool | |
Custom Battery Settings? Inaccurate Wh readings? by dfelz on Wed, 2020-04-08 02:04 |
3 |
by starset Wed, 2021-01-13 22:54 |
VESC Tool | |
FFT in VESC Tool by RSR on Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
VESC Tool | |
One trasmitter two receivers by vikiki on Wed, 2021-11-17 20:40 |
4 |
by Johnvoss Fri, 2021-12-24 03:57 |
VESC Tool | |
Hall sensor problems by Traceo on Wed, 2021-11-10 00:05 |
2 |
by Traceo Fri, 2021-11-19 22:35 |
VESC Tool | |
Hall sensor data is all 0. What do? by Byproduct on Sat, 2023-01-14 14:39 |
by Byproduct Wed, 2023-02-08 11:21 |
VESC Tool | ||
2 PWM Inputs by graybilldustin@... on Mon, 2022-06-06 13:48 |
3 |
by frank Tue, 2022-06-21 16:34 |
VESC Tool | |
motor max rpm and current severely limited? by Roy Zhang on Mon, 2021-08-09 19:23 |
2 |
by vadicus Thu, 2021-08-12 04:06 |
VESC Tool | |
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 07:06 |
VESC Tool | ||
Connecting ABI encoder to VESC by Gas_Sn4ke on Mon, 2018-11-26 06:00 |
by Gas_Sn4ke Mon, 2018-11-26 06:00 |
VESC Tool | ||
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
VESC tool 0.94 needed(Linux) by tahirhasan on Wed, 2019-09-11 16:34 |
1 |
by mustafa Sun, 2019-11-10 20:34 |
VESC Tool | |
App. settings: "Enable servo output on PPM-port when PPM-app is disabled." option by alexantosh on Fri, 2021-12-10 09:46 |
by alexantosh Fri, 2021-12-10 09:46 |
VESC Tool | ||
VESC Tool crashes when loading/saving motor/app config by bkyrevolution on Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
VESC Tool |