You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Firmware failure? Updating BLE trough SWD fails by dk-odense on Wed, 2019-11-13 09:07 |
3 |
by frank Thu, 2019-12-05 11:16 |
VESC Firmware | |
|
75/300 connection issues FW3.6 by renaudbarbier on Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
General discussion | |
|
External speed sensor by Victor Bruun on Thu, 2021-02-04 08:59 |
3 |
by czndl Thu, 2021-11-25 21:33 |
Feature Requests | |
|
Open source hardware? by Jens on Thu, 2017-09-14 18:15 |
3 |
by frank Fri, 2017-09-15 14:01 |
General discussion | |
|
VESC 6.0 MCU Model? by josh on Thu, 2018-02-01 03:14 |
3 |
by josh Sat, 2018-02-10 19:17 |
General discussion | |
|
HFI reference paper by jus133 on Mon, 2021-05-03 05:15 |
3 |
by benjamin Sun, 2021-11-07 12:09 |
General discussion | |
|
Uploaded Firmware, Not Updated by kneave on Sat, 2018-08-18 21:02 |
3 |
by Bernardo Moreira Wed, 2025-03-26 12:32 |
VESC Firmware | |
|
position hold below specific duty cycle by lacondro on Wed, 2022-04-27 04:41 |
3 |
by Matevz Tue, 2025-11-18 14:17 |
VESC Firmware | |
|
ESC FS75100 by myck33 on Fri, 2021-12-31 14:17 |
3 |
by LJB1979 Thu, 2026-02-26 00:58 |
VESC Firmware | |
|
[Solved]Command the throttle (ADC1) with a DAC by captaintoon on Sat, 2024-01-27 23:41 |
3 |
by captaintoon Sun, 2024-01-28 15:44 |
General discussion | |
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu on Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
VESC Original Hardware | |
|
Change maximum allowed input voltage by CTSchorsch on Mon, 2021-12-13 21:37 |
3 |
by Er-Chispa Mon, 2025-10-06 18:05 |
Third Party Hardware | |
|
Flipsky 4.12 Vesc in FOC mode? by Jonny254 on Sat, 2018-09-08 11:25 |
3 |
by Jonny254 Thu, 2018-09-13 05:48 |
Third Party Hardware | |
|
DIYElectricSkateboard.com Torque Board Street: DOA by epretorious on Thu, 2022-06-02 17:54 |
3 |
by frank Sat, 2022-06-04 11:50 |
Third Party Hardware | |
|
Analog Throttle/Brake -- ADC2 does NOT cut power to the throttle? What is wrong? by 010203040506070809 on Fri, 2019-09-20 07:57 |
3 |
by striderkent Fri, 2019-09-20 21:54 |
General discussion | |
|
Is there a way to use the 5 pin hall sensor with VESC? by Shivanshu Mahim on Fri, 2020-11-20 11:02 |
3 |
by Shivanshu Mahim Sat, 2020-11-21 19:34 |
General discussion | |
|
VESC 4.12 firmware 3.38 flash back to firmware 2.18 by Arm007 on Thu, 2019-04-11 08:30 |
3 |
by skyline1970 Fri, 2019-08-02 15:15 |
VESC Firmware | |
|
Type of Hall sensor by Faheem on Thu, 2023-10-12 05:52 |
3 |
by Faheem Mon, 2023-10-23 10:02 |
General discussion | |
|
forum email notifications by jlcortex on Tue, 2018-06-05 15:30 |
3 |
by kubark42 Tue, 2021-10-05 21:15 |
General discussion | |
|
VESC 6+ CAN bus continued by kimpet on Fri, 2019-04-26 13:27 |
3 |
by Tinkerer Fri, 2021-04-02 06:31 |
General discussion |
Pages
