You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
bootloader destroied by notger on Tue, 2017-09-19 19:55 |
3 |
by dinamee Sat, 2018-01-13 10:09 |
General discussion | |
|
Always get Fault:DRV in FOC mode during startup . by stone_1706 on Sat, 2019-02-02 17:35 |
3 |
by stone_1706 Tue, 2019-02-12 03:20 |
General discussion | |
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 on Sun, 2023-02-05 18:00 |
3 |
by mvturnho Wed, 2025-05-14 08:46 |
VESC Firmware | |
|
Wiring a touchscreen to a vesc by posthy on Tue, 2022-06-14 10:22 |
3 |
by frank Thu, 2022-06-16 08:35 |
General discussion | |
|
Version 0.84, some problems with ADC, see 2nd post please! by ThierryGTLTS on Sun, 2017-10-29 14:11 |
3 |
by ThierryGTLTS Fri, 2017-11-03 16:56 |
VESC Tool | |
|
What is the recommended way to implement a new encoder in the VESC firmware? by toma on Mon, 2019-11-04 00:19 |
3 |
by James Donker Mon, 2025-01-27 18:53 |
VESC Firmware | |
|
100k NTC by CTSchorsch on Tue, 2019-05-07 17:18 |
3 |
by Roger Wolff Sat, 2019-05-11 13:00 |
General discussion | |
|
Mini/micro/nano VESC solutions? by Cham on Mon, 2020-09-21 17:34 |
3 |
by Cham Thu, 2020-09-24 12:15 |
Third Party Hardware | |
|
single micro multiple driver support by Robert lloyd on Thu, 2018-07-26 11:58 |
3 |
by TheFallen Thu, 2018-08-23 10:08 |
VESC Firmware | |
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried on Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
VESC Tool | |
|
Motor temperature, how to set limit >120 C ? by RSR on Wed, 2018-08-22 12:40 |
3 |
by Danny Bokma Thu, 2018-08-23 07:19 |
VESC Tool | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
VESC100/250 - motor current setting ignored? by tobiokanobi on Mon, 2022-05-02 13:27 |
3 |
by frank Tue, 2022-05-03 20:54 |
VESC Tool | |
|
Error 500 on older private messages by TechAUmNu on Wed, 2018-05-09 23:15 |
3 |
by Roger Wolff Mon, 2018-05-14 10:06 |
General discussion | |
|
when speed of vesc motor too fast and the arduino pin signal is unstable by HumorLogic on Tue, 2021-04-06 14:21 |
3 |
by woliam Sat, 2021-04-10 15:17 |
General discussion | |
|
Best hardware platform for firmware development by kubark42 on Thu, 2021-10-14 19:59 |
3 |
by district9prawn Wed, 2021-10-20 00:01 |
Third Party Hardware | |
|
impossible to post new feature request by player107 on Wed, 2022-12-07 08:15 |
3 |
by frank Fri, 2022-12-09 14:28 |
General discussion | |
|
Makerbase (new) 84200hp 'quirky' on/off 'bug'? by flez1966 on Wed, 2024-03-20 17:06 |
3 |
by Huang_jh Thu, 2024-10-17 13:24 |
Third Party Hardware | |
|
Optimizing VESC6 setup for my Giant Lego Go-Kart project by mantisrobot on Thu, 2020-06-18 13:29 |
3 |
by TechAUmNu Mon, 2020-06-29 10:19 |
General discussion | |
|
Sending RPM via UART to STM32 by EmirDns on Sat, 2022-01-08 11:00 |
3 |
by EmirDns Mon, 2022-02-07 17:38 |
General discussion |
Pages
