You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Set and measure RPM - Questions by Piep on Thu, 2018-11-08 16:10 |
by Piep Thu, 2018-11-08 16:10 |
General discussion | ||
|
How does controlling two different motors over CAN bus really work? by oangelo on Sat, 2023-04-15 20:05 |
by oangelo Sat, 2023-04-15 20:05 |
General discussion | ||
|
Sign of ADC current readings - ia & ib by RaiNFall on Mon, 2021-05-17 08:21 |
by RaiNFall Mon, 2021-05-17 08:21 |
VESC Firmware | ||
|
Watchdog reset not locatable by edilger on Sun, 2024-05-19 14:29 |
by edilger Sun, 2024-05-19 14:29 |
VESC Firmware | ||
|
open gl issue by TONY61 on Fri, 2025-12-19 17:00 |
by TONY61 Fri, 2025-12-19 17:00 |
VESC Tool | ||
|
Trouble with FSESC75200 by Erik on Wed, 2020-10-07 19:09 |
by Erik Tue, 2020-10-13 15:07 |
Third Party Hardware | ||
|
read RPM over CAN by nblange on Mon, 2021-05-03 20:43 |
by nblange Mon, 2021-05-03 20:43 |
VESC Tool | ||
|
VESC packet fram-size by Yosh101 on Fri, 2022-09-30 15:34 |
by Yosh101 Fri, 2022-09-30 15:34 |
General discussion | ||
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 on Sun, 2019-10-27 22:52 |
by samuelis01 Sun, 2019-10-27 22:52 |
VESC Firmware | ||
|
Minimum System Requirements for VESC Tool 3.01 under Windows by j.konrad on Mon, 2022-01-24 21:48 |
by j.konrad Mon, 2022-01-24 21:48 |
VESC Tool | ||
|
Rickshaw Motor - Typical 48V 1000W motors available by sweendog311 on Wed, 2023-09-20 22:52 |
by sweendog311 Wed, 2023-09-20 22:52 |
General discussion | ||
|
Sinusoidal commutation by shaman on Wed, 2020-06-03 23:42 |
by shaman Wed, 2020-06-03 23:42 |
Feature Requests | ||
|
Using Hall as encoder input by Offline on Tue, 2021-01-19 10:41 |
by Offline Mon, 2021-02-08 10:19 |
General discussion | ||
|
NEW HARDWARE RELEASED!!! | DF_ESC Electric Motor Controller | YouTube Series Walkthrough by d.fresu on Mon, 2023-08-14 18:29 |
by d.fresu Mon, 2023-08-14 18:29 |
General discussion | ||
|
Multiple VESCs on the same battery by Riccio on Wed, 2022-04-20 22:09 |
by Riccio Wed, 2022-04-20 22:09 |
General discussion | ||
|
duty cicle 95% but current not at max by rodrigo.baronio on Mon, 2023-02-06 15:52 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
VESC Tool | ||
|
can't communicate with arduino nrf by m.juan on Mon, 2018-07-02 16:57 |
by m.juan Mon, 2018-07-02 16:57 |
General discussion | ||
|
VESC Replacing Shunt Resistor with Hall Current Sensor？ by happy85 on Fri, 2025-07-18 06:21 |
by happy85 Fri, 2025-07-18 11:51 |
General discussion | ||
|
Vesc_tool running error by kwlimm on Sun, 2020-01-19 10:01 |
by kwlimm Sun, 2020-01-19 10:01 |
General discussion | ||
|
VESC_75_300 by jk007 on Fri, 2021-03-19 02:41 |
by jk007 Fri, 2021-03-19 02:41 |
VESC Original Hardware |
Pages
