You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Power cutoff without any warning by TylerWilson on Fri, 2022-12-09 06:37 |
by TylerWilson Fri, 2022-12-09 07:11 |
General discussion | ||
Trampa boards online store by jrowe on Tue, 2019-04-16 06:28 |
by jrowe Tue, 2019-04-16 06:28 |
VESC Original Hardware | ||
VESC Connections by shatty on Sat, 2021-03-06 21:49 |
by shatty Sat, 2021-03-06 21:51 |
VESC Original Hardware | ||
Motor and input calibration without drive train by technique on Tue, 2020-07-14 19:22 |
by technique Tue, 2020-07-14 19:22 |
VESC Tool | ||
MAX ERPM by riderman on Sun, 2021-02-28 23:05 |
by riderman Sun, 2021-02-28 23:05 |
VESC Tool | ||
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
Position Control with Resolver by robo_studienarbeit on Tue, 2018-10-16 18:57 |
by robo_studienarbeit Tue, 2018-10-16 18:57 |
General discussion | ||
mxus xf15 thermistor by ligi on Tue, 2021-05-18 09:43 |
by ligi Tue, 2021-05-18 09:43 |
General discussion | ||
Detection for a drone outrunner 515 kV and 775 kV by MaksK on Thu, 2020-06-04 16:05 |
by MaksK Thu, 2020-06-04 16:05 |
VESC Tool | ||
ADC out of bounds voltage still maps?! by Matt6288 on Tue, 2021-01-12 02:27 |
by Matt6288 Tue, 2021-01-12 02:27 |
Feature Requests | ||
App Bounty $200 by Johnvoss on Mon, 2021-08-16 05:04 |
by Johnvoss Mon, 2021-08-16 05:05 |
Feature Requests | ||
Motor compatibility (and power levels) by MrSurly on Tue, 2022-04-12 21:43 |
by MrSurly Tue, 2022-04-12 21:43 |
General discussion | ||
FSESC 4.2 motor power limited in sensored mode by motion_sickness on Mon, 2023-01-30 01:47 |
by motion_sickness Thu, 2023-02-02 18:25 |
Third Party Hardware | ||
servo input by Roger Wolff on Tue, 2018-07-03 07:50 |
by Roger Wolff Tue, 2018-07-03 07:50 |
VESC Firmware | ||
Motor command in log? by carboninfusion on Tue, 2020-08-04 07:58 |
by carboninfusion Tue, 2020-08-04 07:59 |
VESC Tool | ||
Need help maximizing torque at low RPM - FOC, Hub motors, Flipsky VESC 4.12 50A by Bruce on Mon, 2021-03-15 03:31 |
by Bruce Mon, 2021-03-15 03:31 |
General discussion | ||
Clicking File Location settings reset input configuration. Bug? by tiztrain on Mon, 2022-07-25 03:34 |
by tiztrain Mon, 2022-07-25 03:34 |
VESC Tool | ||
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
General discussion | ||
The rpm control is not working properly by ptss37 on Wed, 2021-11-24 03:30 |
by ptss37 Wed, 2021-11-24 03:44 |
General discussion | ||
How to control a vesc controller without pulling electric wires on a bike? by peignier jacques on Sat, 2020-04-11 09:20 |
by peignier jacques Sat, 2020-04-11 09:21 |
Feature Requests |