You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Troubleshooting Newborn VESC by vadicus on Tue, 2019-04-09 02:13 |
3 |
by vadicus Tue, 2019-05-14 02:06 |
Third Party Hardware | |
|
Truncated maximum motor current values by kaxorpie on Sun, 2020-12-27 23:28 |
5 |
by kaxorpie Wed, 2020-12-30 00:16 |
Feature Requests | |
|
Trying to build a can sniffer for vesc with an esp32 by Duz on Fri, 2024-07-19 19:45 |
by Duz Fri, 2024-07-19 19:45 |
Projects incorporating VESC technology | ||
|
Trying to connect over USB, but new 6.4 connects and disconnects a few seconds later. by MaxMaker1 on Thu, 2018-05-24 16:15 |
12 |
by frank Thu, 2019-02-21 20:34 |
VESC Tool | |
|
Trying to make motor-control work for predetermined motions, could use some help by Davideo on Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
General discussion | |
|
Trying to read and set MCCONF by Jamie42 on Tue, 2020-03-24 19:47 |
by Jamie42 Tue, 2020-03-24 19:47 |
General discussion | ||
|
Trying to run a refrigerant compressor's BLDC with VESC by logansheaf on Wed, 2025-01-29 02:01 |
2 |
by logansheaf Wed, 2025-01-29 23:23 |
General discussion | |
|
Trying to upgrade old Enertion FOCBOX Fw 2.18 by jyl087 on Fri, 2024-09-13 16:26 |
by jyl087 Fri, 2024-09-13 17:31 |
Third Party Hardware | ||
|
Tuning Advanced Settings For BLDC by DjSourD on Wed, 2020-08-26 05:51 |
1 |
by trademarkaaron Tue, 2023-11-28 18:42 |
General discussion | |
|
tuning PID speed for the skateboard motor with hall sensors by salviador on Tue, 2021-09-14 14:37 |
1 |
by skyline1970 Sat, 2021-09-18 11:18 |
General discussion | |
|
Tuning process? by wingborne on Tue, 2020-09-29 00:09 |
by wingborne Tue, 2020-09-29 21:39 |
General discussion | ||
|
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 on Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
General discussion | |
|
Tuning strategy for a large motor? by MrSurly on Tue, 2022-11-01 06:51 |
1 |
by vadicus Mon, 2022-11-14 18:23 |
General discussion | |
|
Turn on VESC via CAN Message by castiaum on Thu, 2022-06-02 12:17 |
1 |
by frank Thu, 2022-06-02 15:14 |
VESC Firmware | |
|
Turnigy Sk8 ESC - pulls voltage to zero by mnetterberg on Wed, 2021-09-29 10:17 |
1 |
by skyline1970 Mon, 2021-11-01 07:55 |
Third Party Hardware | |
|
Twisted pair for Can Bus link cable? by Kenny-san650 on Tue, 2018-02-13 08:35 |
2 |
by Kenny-san650 Mon, 2018-02-19 09:15 |
VESC Firmware | |
|
TWO MOTOR SYSTEM by ronmotor on Mon, 2022-10-17 00:44 |
by ronmotor Mon, 2022-10-17 00:44 |
VESC Tool | ||
|
Two Motors on same Shaft by Giga93 on Thu, 2017-12-14 10:12 |
5 |
by ThierryGTLTS Sun, 2017-12-17 13:20 |
General discussion | |
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann on Wed, 2021-04-21 13:48 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
VESC Tool | ||
|
Two phase modulation by jguy on Sat, 2023-12-09 13:33 |
4 |
by jguy Fri, 2023-12-15 11:49 |
General discussion |
Pages
