You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
where to source BLDC 6.5in geared wheel? by fourchette on Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
General discussion | |
|
Disable throttle while braking by rl_19 on Sat, 2022-03-19 00:05 |
7 |
by flez1966 Thu, 2024-03-21 09:41 |
General discussion | |
|
VESC Logo by beachbrojoe on Thu, 2022-12-08 19:37 |
1 |
by frank Fri, 2022-12-09 14:24 |
General discussion | |
|
Controller (VESC 6 based) dont like small motor by matrixgti on Mon, 2024-01-29 21:27 |
by matrixgti Fri, 2024-02-23 15:37 |
General discussion | ||
|
VESC in-air startup failure by jschall on Sat, 2025-04-26 00:56 |
2 |
by jschall Sat, 2025-04-26 01:32 |
General discussion | |
|
vesc tool page not opening by bsissell on Sun, 2021-11-21 20:46 |
1 |
by velolac Sun, 2021-11-21 22:13 |
General discussion | |
|
Motor Controller Recommendations - 84V max - 50A Continuous by dylanu on Thu, 2021-11-11 22:54 |
5 |
by mikael Sat, 2023-09-30 01:46 |
General discussion | |
|
ignore this by tobe81cwb on Tue, 2022-06-21 18:51 |
by tobe81cwb Tue, 2022-07-19 16:44 |
General discussion | ||
|
Bench Testing by usaevo7 on Tue, 2023-04-25 16:50 |
by usaevo7 Tue, 2023-04-25 16:50 |
General discussion | ||
|
Hall sensor filter on VESC flier board by raess on Tue, 2018-03-27 21:00 |
17 |
by raess Wed, 2018-04-11 13:43 |
General discussion | |
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho on Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
General discussion | |
|
Because..why not: Full Self Riding Skateboard (autonomous skateboard) by x78163 on Wed, 2022-06-08 17:33 |
by x78163 Wed, 2022-06-08 17:33 |
General discussion | ||
|
VESC 6 DC motor Current limit? by ShortCircuit on Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
General discussion | |
|
Connecting the VESC6 plus with servo wires by GreenPenguin on Wed, 2019-10-16 15:39 |
1 |
by frank Thu, 2019-10-17 11:11 |
General discussion | |
|
VESC 75/300 and EMC Tests for motorcycle conversion by gotfatalErrs on Tue, 2020-06-02 18:34 |
8 |
by Bubu54 Wed, 2024-09-04 13:52 |
General discussion | |
|
Negative current reporting at high erpm in no-load setup by mcdanny on Sun, 2021-01-17 23:04 |
1 |
by moto_guy Sat, 2021-01-30 04:53 |
General discussion | |
|
FlipSky 75/300 + Alien 80 KV noise/vibration under load by brendangillatt on Thu, 2021-01-07 01:19 |
13 |
by Thejesh Bollineni Wed, 2025-04-30 22:49 |
General discussion | |
|
VESC 4.12 FW5.02 CAN status messages is spamming bus, external controller, SOLVED: NEEDED INIT! by Offline on Mon, 2021-05-03 14:57 |
1 |
by Offline Tue, 2021-05-04 10:03 |
General discussion | |
|
Mid-drive ebikes? by Zoltan on Fri, 2022-01-28 16:37 |
3 |
by frank Thu, 2022-02-03 08:51 |
General discussion |
Pages
