You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Setting PI / PID controllers in VESC for very low speeds. For CNC by K@RLSON on Sat, 2020-01-25 21:06 |
9 |
by Luke264 Wed, 2021-02-17 18:52 |
General discussion | |
|
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
|
Setting RPM over UART by klay2000 on Sat, 2024-06-29 01:27 |
by klay2000 Sat, 2024-06-29 01:28 |
General discussion | ||
|
Setting the minimum ERPM in FOC mode? by mathias on Sat, 2018-06-16 02:20 |
by mathias Sat, 2018-06-16 02:20 |
Feature Requests | ||
|
Setting the motor parameters by Lenar on Sat, 2024-05-04 10:18 |
by Lenar Sat, 2024-05-04 10:18 |
General discussion | ||
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis on Fri, 2020-05-22 07:34 |
2 |
by thefallen Wed, 2020-05-27 08:59 |
VESC Original Hardware | |
|
setting up development environment for android by jaghori.sasan on Wed, 2019-02-20 14:59 |
by jaghori.sasan Wed, 2019-02-20 14:59 |
VESC Tool | ||
|
Setting up flipsky by JanneHooo on Sat, 2023-10-14 13:07 |
2 |
by JanneHooo Sun, 2023-10-15 13:18 |
General discussion | |
|
Setting up Flipsky 4.2 Dual and VX2 remote FW issues - Please help by Rashid1992 on Wed, 2020-12-23 17:13 |
7 |
by MartyMcFlyFord Mon, 2022-05-23 14:44 |
VESC Firmware | |
|
Setting up low KV brushless motor? by Trent on Sun, 2019-12-01 02:09 |
4 |
by Trent Wed, 2019-12-04 07:54 |
General discussion | |
|
Settings by aquamarin on Sat, 2023-07-01 16:11 |
by aquamarin Sat, 2023-07-01 16:11 |
General discussion | ||
|
Setup FOC automaticly without vesc tool ihm by NATUITION on Tue, 2024-04-16 10:11 |
by NATUITION Tue, 2024-04-16 10:11 |
VESC Tool | ||
|
SETUP FOR SINGLE BRUSHED MOTOR by mmatthews@aquav... on Fri, 2022-05-13 01:57 |
1 |
by skyline1970 Thu, 2022-11-24 21:39 |
General discussion | |
|
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
|
Setup motor foc by Vincent LAMBERT on Thu, 2022-02-03 12:22 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
VESC Tool | ||
|
Setup parameters for battery in VESC Tool by Ulrich on Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
VESC Tool | |
|
Several questions and safe values by miskuhunor@gmail.com on Thu, 2021-09-09 08:33 |
by miskuhunor@gmail.com Thu, 2021-09-09 08:33 |
VESC Tool | ||
|
Should I drive a HDD motor with VESC or some other chip? by arildj78 on Tue, 2018-05-22 09:09 |
1 |
by arildj78 Wed, 2018-05-23 12:26 |
General discussion | |
|
should i update my unity to get the latest update for stormcore app? by kylewardbro on Fri, 2020-10-30 19:30 |
by kylewardbro Fri, 2020-10-30 19:30 |
VESC Firmware | ||
|
Show actual encoder RPM by Enak on Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
Feature Requests |
Pages
