You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Probably first dead VESC SIX by Squad on Tue, 2017-06-27 14:00 |
8 |
by frank Thu, 2017-08-17 22:31 |
VESC6 Beta | |
|
Step by Step Setup by frank on Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
VESC Tool | |
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
|
Vesc 100/250 (Trampa board) wiring for ebike by Oded Mazor on Fri, 2022-03-18 23:34 |
8 |
by Markula Fri, 2022-04-01 09:21 |
General discussion | |
|
Flipsky HC 200A VESC programming to eFoil motor by tylerclark on Wed, 2020-03-11 05:52 |
8 |
by okarbon Tue, 2021-02-23 13:19 |
VESC Firmware | |
|
Failure of FOC mode brake by jzy1115 on Sun, 2018-03-25 10:23 |
8 |
by iscle Sun, 2018-07-15 19:19 |
General discussion | |
|
4 BLDC for 1 VESC by mac_cros on Wed, 2019-03-20 16:45 |
8 |
by tul00985 Wed, 2019-04-03 08:32 |
Third Party Hardware | |
|
Flipsky FSESC75100 & FSESC75200 Phase Filtering by j.konrad on Sat, 2022-04-02 00:17 |
8 |
by Prolive Tue, 2022-08-02 17:42 |
Third Party Hardware | |
|
I need help designing 200v 80a vesc by qwerasdf on Mon, 2021-05-03 17:08 |
8 |
by dylanu Thu, 2022-04-14 06:29 |
Third Party Hardware | |
|
VESC 6 Schematic Question by mendez on Tue, 2019-02-12 07:11 |
8 |
by frank Thu, 2019-12-05 11:28 |
VESC Original Hardware | |
|
foc openloop not starting motor on higher erpm by Alan oldguy on Thu, 2018-09-06 08:43 |
8 |
by technicc Mon, 2022-03-28 09:23 |
VESC Tool | |
|
Max Switching Frequency FOC by tuloski on Thu, 2018-09-13 10:37 |
8 |
by Maxim Gridin Thu, 2018-11-22 21:47 |
VESC Firmware | |
|
Missing Braking Power in ADC by Silverline on Wed, 2019-06-12 19:48 |
8 |
by positiv Fri, 2020-01-24 14:07 |
VESC Tool | |
|
"Could not read Firmware version" when connecting via Bluetooth by ligi on Tue, 2020-11-17 07:03 |
8 |
by xxx1den1xxx Sun, 2022-06-05 11:13 |
General discussion | |
|
VSEC firmware update issue by dsuresh on Thu, 2021-02-11 17:25 |
8 |
by Macc Fri, 2021-06-11 13:10 |
General discussion | |
|
Vesc 1.26 BLE Scan error by huzaini on Mon, 2019-12-16 17:17 |
8 |
by sirAnton Sun, 2020-08-09 15:55 |
VESC Tool | |
|
Using dual VESC for Robot Control by Praveen on Sat, 2021-11-13 11:02 |
8 |
by Autocar Tue, 2021-12-07 21:30 |
General discussion | |
|
Is this kogging and jitter in low rpms expected? by Snabelost on Sat, 2022-10-22 16:53 |
8 |
by Snabelost Fri, 2022-10-28 16:07 |
General discussion | |
|
Newbie Help - ADC input by nickyg on Tue, 2020-04-28 11:05 |
8 |
by velolac Fri, 2021-12-10 19:40 |
General discussion | |
|
VESC with propeller, not reaching max performance by ogent on Tue, 2022-02-01 16:31 |
8 |
by ogent Thu, 2022-02-03 14:54 |
VESC Firmware |
Pages
