You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Can someone please post the steps to do position control from vesc tool? by dp on Wed, 2022-02-16 14:51 |
1 |
by frank Wed, 2022-02-16 17:24 |
General discussion | |
Can someone help me understand why I've burned up a DRV8302 in less than 10 seconds? by shimdidly on Fri, 2017-10-13 02:01 |
3 |
by shimdidly Mon, 2017-10-16 17:13 |
General discussion | |
CAN sends error frame by dgarciasoto on Wed, 2022-04-27 07:11 |
by dgarciasoto Wed, 2022-04-27 07:11 |
VESC Firmware | ||
CAN not working on VESC MkV by chundri on Tue, 2021-01-12 15:06 |
1 |
by chundri Wed, 2021-01-13 15:48 |
VESC Original Hardware | |
Can not update firmware on FLIPSKY 4.12, still af 3.4 (att. newbie) by SlinBin on Wed, 2019-03-27 21:59 |
11 |
by thewho Thu, 2020-07-16 18:06 |
Third Party Hardware | |
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
Can not run again after run perfectly !! Pls help by Streetstar69 on Tue, 2021-11-23 03:03 |
1 |
by frank Tue, 2021-11-23 10:03 |
General discussion | |
Can not adjust the RPM on my 1350 w motor by Arne Norway on Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
General discussion | |
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
Can larger BLDC motors be controlled with VESC? by Heimfried on Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
General discussion | |
Can I use 12V power supply? by ryde6 on Sun, 2021-04-25 08:19 |
2 |
by vadicus Wed, 2021-07-14 21:01 |
General discussion | |
Can I re-use an old Galaxy S3 to run the VESC tool? by Munkyheed on Fri, 2019-08-02 20:00 |
by Munkyheed Fri, 2019-08-02 20:00 |
VESC Tool | ||
can I fit a VESC in my e-skate? by 6diegodiego9 on Thu, 2021-01-21 20:42 |
1 |
by skyline1970 Tue, 2021-02-02 21:30 |
General discussion | |
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle on Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
General discussion | |
Can I change control mode on the fly through the UART port? by spork on Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
General discussion | |
CAN eRPM report by alxsfrm on Mon, 2022-02-07 11:01 |
by alxsfrm Mon, 2022-02-07 11:01 |
General discussion | ||
CAN defect? 4WD - CAN does not detect anymore... HELP! by MountainBen on Tue, 2021-02-02 04:04 |
3 |
by skyline1970 Fri, 2021-02-05 19:50 |
Third Party Hardware | |
Can control Vesc 100/250 by David_1 on Sat, 2022-06-18 01:31 |
1 |
by David_1 Sun, 2022-06-19 19:44 |
General discussion | |
CAN Commands to control VESC 100/250? by harmander_sihra on Fri, 2021-12-17 01:49 |
1 |
by tecnico.solarboat Mon, 2021-12-27 23:29 |
VESC Original Hardware | |
CAN bus support not enabled in this build of vesc tool? by Tsomo on Fri, 2021-10-01 09:48 |
17 |
by s54mtb Thu, 2023-05-11 20:10 |
VESC Tool |