You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
single VESC 6+ controlled by CAN-bus by vinci on Fri, 2021-07-09 15:42 |
1 |
by yuri12 Wed, 2022-02-09 17:23 |
VESC Tool | |
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto on Sun, 2022-11-27 16:34 |
by Miniproto Sun, 2022-11-27 16:34 |
VESC Tool | ||
Download latest VESC Tool version by consti on Wed, 2022-06-15 17:24 |
1 |
by frank Thu, 2022-06-16 10:19 |
VESC Tool | |
Parameters for efoil by vladek on Thu, 2023-04-20 12:54 |
by vladek Thu, 2023-04-20 12:54 |
VESC Tool | ||
Kindly delete - Install problem was resolved on a different computer by RobCat on Tue, 2020-03-17 02:48 |
by RobCat Tue, 2020-03-17 03:03 |
VESC Tool | ||
vesc UART with arduino 33 BLE by amaussa on Mon, 2020-10-12 16:57 |
2 |
by Seb44120 Fri, 2020-11-20 23:06 |
VESC Tool | |
Setup motor foc by Vincent LAMBERT on Thu, 2022-02-03 12:22 |
by Vincent LAMBERT Thu, 2022-02-03 12:22 |
VESC Tool | ||
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies on Wed, 2021-04-28 23:59 |
2 |
by Gloobox Wed, 2022-11-30 18:39 |
VESC Tool | |
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Tool | ||
Lisp scripting questions/suggestions/remarks by Gatze on Sun, 2022-04-24 12:13 |
by Gatze Sun, 2022-04-24 13:00 |
VESC Tool | ||
ADC Input Change by alivedom on Thu, 2017-12-14 15:18 |
6 |
by andrecorreia Thu, 2021-04-29 14:44 |
VESC Tool | |
Flipsky nrf51288 by Idoff on Tue, 2018-12-11 21:33 |
2 |
by frank Mon, 2019-02-18 09:00 |
VESC Tool | |
TWO MOTOR SYSTEM by ronmotor on Mon, 2022-10-17 00:44 |
by ronmotor Mon, 2022-10-17 00:44 |
VESC Tool | ||
Motor Values in VESC-Tool 2019 by frank on Wed, 2019-02-27 09:40 |
18 |
by Billy N Fri, 2021-03-26 07:22 |
VESC Tool | |
Erpm / torque setting with remote control, Vesc wand by Lasse on Fri, 2021-02-05 22:41 |
1 |
by skyline1970 Tue, 2021-02-09 20:03 |
VESC Tool | |
Position issue by Davideo on Tue, 2017-09-19 16:48 |
3 |
by bOneWheel Mon, 2023-10-30 15:07 |
VESC Tool | |
Setup for very slow < 100RPM on Maytech 6365 Motor. by jason3w on Tue, 2020-09-01 10:52 |
2 |
by asapereira Mon, 2020-09-14 10:26 |
VESC Tool | |
RT Data Logging by adas29 on Wed, 2023-04-26 22:59 |
by adas29 Wed, 2023-04-26 22:59 |
VESC Tool | ||
Battery LTO Titanate by Mottet on Mon, 2022-06-13 16:34 |
1 |
by electricfox Tue, 2022-06-14 06:28 |
VESC Tool | |
How do I compile the VESC Tool? by ipbyrne on Wed, 2019-07-24 16:58 |
4 |
by a.dahhak Fri, 2021-01-01 15:25 |
VESC Tool |