You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Mini/micro/nano VESC solutions? by Cham on Mon, 2020-09-21 17:34 |
3 |
by Cham Thu, 2020-09-24 12:15 |
Third Party Hardware | |
|
VESC setup question for a motorised rope ascender. by Ben26 on Wed, 2024-10-02 18:57 |
3 |
by Ben26 Fri, 2024-10-18 01:08 |
General discussion | |
|
How to select in VESC Tool the COM port of PC for USB connection to VESC6? by Heimfried on Mon, 2020-05-11 20:27 |
3 |
by Heimfried Wed, 2020-06-10 11:54 |
VESC Tool | |
|
UART Accel/Gyro/Mag data by NATUITION on Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
General discussion | |
|
Motor dosent run normaly, it jerky like crazy. by lumosi on Fri, 2021-03-05 20:36 |
3 |
by dsuresh Wed, 2021-03-10 19:54 |
General discussion | |
|
Maximum cable lengths between VESC, battery pack and motor? by sandersesurf on Sun, 2024-01-14 07:55 |
3 |
by bww129 Fri, 2024-03-15 05:46 |
General discussion | |
|
can't reach the maximum speed by kingpon on Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
General discussion | |
|
Flux linkage detection failed by Count1310 on Sat, 2020-08-22 16:30 |
3 |
by drummerboy5408 Wed, 2022-04-13 07:42 |
General discussion | |
|
Downloading VESC tool on a mac? by Taliesin on Mon, 2018-04-30 01:28 |
3 |
by txdad Fri, 2021-08-27 17:41 |
General discussion | |
|
Initial startup time by rxty on Thu, 2022-06-02 18:38 |
3 |
by sifourquier Sun, 2024-02-25 23:16 |
VESC Firmware | |
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
Bus bar and heavy copper PCBs by lopezcontreras on Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
Third Party Hardware | |
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware | |
|
FFT in VESC Tool by RSR on Thu, 2018-05-31 14:37 |
3 |
by TechAUmNu Thu, 2018-05-31 16:28 |
VESC Tool | |
|
Adding support for three phase shunts... by Roger Wolff on Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
VESC Firmware | |
|
Mosfet Discussion by WalterWitt on Mon, 2022-04-18 20:38 |
3 |
by vadicus Thu, 2022-04-21 00:01 |
Third Party Hardware | |
|
DRV 8302 Under Voltage error by Oyta on Fri, 2017-09-01 20:52 |
3 |
by benjamin Tue, 2017-09-05 21:39 |
VESC6 Beta | |
|
Programming NRF51822 Module with ST-Link v2 by koralle on Wed, 2018-07-11 12:06 |
3 |
by koralle Sun, 2018-07-15 01:28 |
General discussion | |
|
Controlling general BLDC motors by sinned6915 on Wed, 2020-08-19 01:56 |
3 |
by TheFallen Sun, 2020-08-23 16:51 |
General discussion | |
|
Maker X Mini VESC burned at 46V. My fault or shitty quality? by smileandbeware on Mon, 2019-11-18 10:53 |
3 |
by frank Thu, 2019-12-26 15:27 |
Third Party Hardware |
Pages
