You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
How to read MotorRPM from UART to Arduino by azobe on Thu, 2018-03-08 14:42 |
3 |
by Pimousse Mon, 2018-09-03 14:31 |
General discussion | |
|
Trampa 100/250 with one old brushed DC motor....how can i change the motor spin direction????plz help!!! by Asi on Fri, 2022-11-18 12:45 |
3 |
by frank Sat, 2022-11-19 14:55 |
General discussion | |
|
Vesc can't connect to vesc tool by Roansky1 on Sat, 2022-04-30 13:05 |
3 |
by frank Tue, 2022-05-03 20:52 |
VESC Tool | |
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
UART Accel/Gyro/Mag data by NATUITION on Sat, 2019-12-28 11:25 |
3 |
by NATUITION Tue, 2020-01-07 22:14 |
General discussion | |
|
can't reach the maximum speed by kingpon on Sat, 2017-10-28 04:55 |
3 |
by elektrinis Tue, 2018-04-17 21:50 |
General discussion | |
|
CAN defect? 4WD - CAN does not detect anymore... HELP! by MountainBen on Tue, 2021-02-02 04:04 |
3 |
by skyline1970 Fri, 2021-02-05 19:50 |
Third Party Hardware | |
|
Upload bootloader to stm32 f405? by jneumann on Sat, 2020-08-08 07:11 |
3 |
by TechAUmNu Sat, 2020-08-08 18:29 |
General discussion | |
|
Do I need phase voltage sense? by Flepple on Mon, 2021-01-25 15:31 |
3 |
by GPereira Thu, 2022-02-10 11:43 |
General discussion | |
|
Question on throttle response by petermarcotte1 on Wed, 2020-07-29 11:28 |
3 |
by petermarcotte1 Sat, 2020-08-01 14:17 |
General discussion | |
|
firmware V6.06 vs VESC tool V6.05 by shuang on Thu, 2024-12-05 06:49 |
3 |
by Polyloop Mon, 2025-03-31 17:34 |
VESC Firmware | |
|
Power levels by vescbeginer on Wed, 2023-08-16 22:20 |
3 |
by vadicus Wed, 2023-08-23 20:58 |
VESC Firmware | |
|
Sub zero temperature VESC412 issues by jetigm on Fri, 2019-02-08 21:12 |
3 |
by sam.vanratt Sun, 2019-02-10 14:07 |
General discussion | |
|
VESC4 phase shunt by Rico on Tue, 2019-05-21 16:09 |
3 |
by svs Thu, 2019-08-08 08:41 |
VESC Firmware | |
|
Discrepancies between VESC Tool 3.01 Motor Settings & XML config file by j.konrad on Sat, 2022-01-15 22:13 |
3 |
by benjamin Mon, 2022-02-21 22:17 |
VESC Tool | |
|
VESC 75/300 vs VESC 100/250 by XBO on Tue, 2021-09-07 19:31 |
3 |
by flyingbrike Wed, 2021-09-08 13:42 |
General discussion | |
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
Built in BLE HD60 not Working by CS on Mon, 2021-08-23 13:21 |
3 |
by frank Thu, 2021-08-26 08:09 |
VESC Original Hardware | |
|
Bus bar and heavy copper PCBs by lopezcontreras on Mon, 2019-01-28 17:40 |
3 |
by galp Thu, 2019-01-31 20:20 |
Third Party Hardware | |
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware |
Pages
