You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
DC MOTOR connected to FLIPSKY 4.20 MINI by CatalinCHIRICA on Mon, 2019-12-02 18:20 |
by CatalinCHIRICA Mon, 2019-12-02 18:20 |
VESC Tool | ||
Changing minimum duty cycle prevents VESC from connecting via USB while ADC throttle is connected by shimdidly on Sun, 2017-10-15 00:48 |
by shimdidly Sun, 2017-10-15 00:48 |
VESC Tool | ||
vesc for helicopter tail rotor / freewheel for duty cycle mode by vladimir757 on Thu, 2020-06-25 14:25 |
3 |
by skyline1970 Thu, 2021-02-04 21:38 |
VESC Tool | |
Parametre for Low RPM Limit by ilan248@gmail.com on Wed, 2019-07-10 11:01 |
1 |
by askker Thu, 2019-07-11 05:04 |
VESC Tool | |
How to set max input voltage to over 57 volts? by johnny5in5 on Thu, 2020-09-24 03:34 |
3 |
by TheFallen Mon, 2021-03-01 16:42 |
VESC Tool | |
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe on Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
VESC Tool | |
Help with a settings for only generator by Mafo on Fri, 2018-03-02 16:59 |
6 |
by Mafo Thu, 2018-03-15 11:15 |
VESC Tool | |
Driving Alternator wired as BLDC motor with VESC6 by LittleTinker on Thu, 2019-10-10 13:06 |
6 |
by flyingbrike Wed, 2021-09-22 20:16 |
VESC Tool | |
Phase Correct PWM Setting? by orangepig111 on Tue, 2021-07-20 07:39 |
1 |
by skyline1970 Fri, 2021-10-29 12:52 |
VESC Tool | |
How to control motor using VESC tool in computer at constant rpm? by vimi94 on Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
VESC Tool | |
Multiple VESC's in duty cycle mode by Rudolf10000 on Sat, 2019-04-20 13:24 |
1 |
by Rudolf10000 Mon, 2019-04-29 19:34 |
VESC Tool | |
ADC MAX Voltage 5volt ? by liteglow on Sat, 2020-07-25 23:48 |
by liteglow Sat, 2020-07-25 23:48 |
VESC Tool | ||
Vesc efficiency through log (.CSV) by th0masrtg on Tue, 2022-11-22 10:08 |
by th0masrtg Tue, 2022-11-22 10:08 |
VESC Tool | ||
Vesc tool 1.26.. issue with firmware updates? by beetbocks on Tue, 2019-12-17 10:17 |
2 |
by Stupidspencer Wed, 2019-12-25 23:04 |
VESC Tool | |
FOC with 2 Poles and only 6 Windings? by martin2day on Fri, 2020-07-17 08:16 |
2 |
by martin2day Sat, 2020-07-18 10:36 |
VESC Tool | |
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
VESC Tool | |
Command Line Options by Dude on Wed, 2017-10-18 22:56 |
6 |
by woodmastr Thu, 2022-07-21 14:23 |
VESC Tool | |
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne on Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
VESC Tool | |
Motor always accelerates to maximum speed by zapshe on Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
VESC Tool | |
VESC Tool app min hardware requirements by flix on Sat, 2022-04-16 22:13 |
by flix Sat, 2022-04-16 22:13 |
VESC Tool |