You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion | |
|
Setting up a VESC 6 MK IV and need 58.2 voltage fault by warrenhdavis on Fri, 2020-05-22 07:34 |
2 |
by TheFallen Wed, 2020-05-27 08:59 |
VESC Original Hardware | |
|
Does Trampa BMS work with multiple VESCs? by kylerlaird on Sun, 2025-04-20 03:57 |
2 |
by kylerlaird Sun, 2025-04-20 15:38 |
VESC Original Hardware | |
|
Duty cycle take 95% when motor released by Rarikao on Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
VESC Firmware | |
|
Battery to motor voltage by fazekas on Sat, 2021-05-15 16:03 |
2 |
by fazekas Sun, 2021-05-16 20:43 |
General discussion | |
|
Motors in PID control stops responding for a few seconds by rcmower on Tue, 2023-10-10 20:49 |
2 |
by rcmower Thu, 2023-10-12 14:19 |
General discussion | |
|
Hall count drift by xachmo on Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
VESC Original Hardware | |
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan on Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
VESC Tool | |
|
Support for AMC1301 powered from bootstrap by antonchromjak on Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
Feature Requests | |
|
Type of motors supported by VESC 6 MKIV by Sami Sahli on Thu, 2020-06-25 11:57 |
2 |
by Samuelx Tue, 2021-08-17 20:24 |
General discussion | |
|
Vx1 controller help by stefann on Wed, 2020-03-11 12:42 |
2 |
by stefann Sun, 2020-03-15 00:36 |
Third Party Hardware | |
|
Big Inrunner - Noisy In FOC Mode by skeaux on Mon, 2020-03-02 04:13 |
2 |
by skeaux Tue, 2020-03-03 05:30 |
General discussion | |
|
How to modify default firmware? by lorenzo211 on Sun, 2018-03-11 19:15 |
2 |
by yosoufe Mon, 2018-03-12 14:17 |
VESC Firmware | |
|
Overheating protection, voltage-/current-limitation etc. by kianK on Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
VESC Tool | |
|
fault_code_high_offset_current_sensor_1 by Enak on Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
VESC Original Hardware | |
|
VESC Firmware (conf_general.h) by HopeAndWonder on Sat, 2020-05-16 20:44 |
2 |
by judylee Thu, 2020-06-18 11:25 |
VESC Firmware | |
|
Help i have no idea how it works... by Xtracker133 on Sat, 2022-12-31 14:55 |
2 |
by Xtracker133 Tue, 2023-01-03 22:52 |
General discussion | |
|
Voltage measurement calibration? by pyryjansson on Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
VESC Tool | |
|
VESC 75/250 v 75/300? by AliBarrett10 on Tue, 2021-07-06 19:50 |
2 |
by Ht Tue, 2021-10-12 07:08 |
VESC Original Hardware | |
|
Looking for VESC Tuning Help will pay $ by jordan73s on Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
General discussion |
Pages
