You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
Logging real time data from a custom app by SirPolPol on Sat, 2021-02-06 22:24 |
by SirPolPol Sat, 2021-02-06 22:24 |
VESC Tool | ||
Android version : ERPM > RPM in RT DATA, a useful refinement by unimotion on Tue, 2020-03-24 10:58 |
by unimotion Tue, 2020-03-24 10:58 |
Feature Requests | ||
Angle offset detection by Gas_Sn4ke on Mon, 2019-01-21 07:09 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
General discussion | ||
Kindly delete - Install problem was resolved on a different computer by RobCat on Tue, 2020-03-17 02:48 |
by RobCat Tue, 2020-03-17 03:03 |
VESC Tool | ||
Several questions and safe values by miskuhunor@gmail.com on Thu, 2021-09-09 08:33 |
by miskuhunor@gmail.com Thu, 2021-09-09 08:33 |
VESC Tool | ||
Setting PID gains (and other config parameters) over CAN Bus by TheCuriousRobot on Thu, 2022-12-15 22:03 |
by TheCuriousRobot Thu, 2022-12-15 22:03 |
General discussion | ||
VESC Tool for Android & GPS/GNSS sharing? by ahagge on Fri, 2021-10-01 05:04 |
by ahagge Fri, 2021-10-01 05:04 |
VESC Tool | ||
Flipsky 6.6 no green/red led only blue by vic1234 on Thu, 2022-05-19 20:46 |
by vic1234 Thu, 2022-05-19 20:46 |
Third Party Hardware | ||
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 on Sun, 2019-10-13 14:22 |
by tahirali1 Sun, 2019-10-13 14:22 |
VESC Original Hardware | ||
VESC back-current safety? by randohinn on Mon, 2019-04-15 16:37 |
by randohinn Mon, 2019-04-15 16:37 |
General discussion | ||
Dual Motor Setup not working via CAN Bus (solved) by acleon on Fri, 2020-06-19 00:03 |
by acleon Fri, 2020-06-19 16:33 |
VESC Tool | ||
VESC apps by bosko on Thu, 2020-01-23 18:28 |
by bosko Thu, 2020-01-23 18:28 |
General discussion | ||
noob question - how to I update FW to 3.66? by brently on Thu, 2020-01-16 02:22 |
by brently Thu, 2020-01-16 02:22 |
VESC Firmware | ||
information to drive 400kv drone motor on ClosedLoop with AS5047 by Syl2078 on Sun, 2019-02-17 19:20 |
by Syl2078 Sun, 2019-02-17 19:20 |
General discussion | ||
Reverse ADC and UART by ben_src on Mon, 2019-08-12 17:22 |
by ben_src Mon, 2019-08-12 17:22 |
General discussion | ||
Where to order plastic sleeve for VESC by braingame26 on Thu, 2019-02-07 16:34 |
by braingame26 Thu, 2019-02-07 16:34 |
Third Party Hardware | ||
Is there a way to deactivate roll to start function FW 5.02 by Philo on Fri, 2021-04-16 22:28 |
by Philo Sun, 2021-04-18 11:57 |
VESC Firmware | ||
Nrf connection error by vufmihai on Sat, 2020-04-25 22:00 |
by vufmihai Sat, 2020-04-25 22:00 |
VESC Tool | ||
Using Motor hall sensors as the encoder by Russ g on Wed, 2019-05-08 16:01 |
by Russ g Wed, 2019-05-08 16:01 |
General discussion | ||
NRF connection error by Denn on Wed, 2022-02-02 11:17 |
by Denn Wed, 2022-02-02 11:17 |
VESC Tool |
Pages
