You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
IPM/Salient Motor Tuning by SRFirefox on Wed, 2020-08-26 23:19 |
2 |
by JP Wed, 2022-08-17 11:22 |
General discussion | |
|
Connect 4 vesc with can-bus, motors stuttering by oyvinla on Tue, 2022-01-04 17:12 |
8 |
by ahanktcd Wed, 2024-04-17 06:35 |
General discussion | |
|
PID Speed Mode not limiting max ERPM by jordan73s on Sat, 2025-05-03 10:57 |
1 |
by colmor Thu, 2025-05-08 22:44 |
General discussion | |
|
Battery percentage mapping by Sharkboy on Mon, 2024-05-06 22:55 |
by Sharkboy Mon, 2024-05-06 22:55 |
General discussion | ||
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Raspberry Pi as TCP Hub/VESC Express by wittrup on Mon, 2025-04-07 10:03 |
1 |
by wittrup Mon, 2025-04-07 13:49 |
General discussion | |
|
Motors spin during detection but then won't spin by jsbenson on Tue, 2023-06-27 23:54 |
by jsbenson Tue, 2023-06-27 23:54 |
General discussion | ||
|
PPM Mislabeled by stevemk14ebr on Fri, 2018-12-21 01:49 |
1 |
by Roger Wolff Tue, 2019-01-01 12:12 |
General discussion | |
|
20S by ahanktcd on Thu, 2024-04-25 14:51 |
by ahanktcd Thu, 2024-04-25 14:51 |
General discussion | ||
|
No load FOC stops when full FWD throttle. by toboli on Mon, 2023-06-05 18:41 |
by toboli Mon, 2023-06-05 18:41 |
General discussion | ||
|
How I control the RPM of my motor from VESC with Arduino? by George W. on Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
General discussion | |
|
*newbie* motors keep running backwards randomly when switch off, and then back on. Embarrassing. by Nikolas Lamshed on Sun, 2021-06-20 13:36 |
by Nikolas Lamshed Sun, 2021-06-20 13:36 |
General discussion | ||
|
2nd Maytech 75_300 burned by Flyingtux on Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
General discussion | |
|
KERS system with a VESC 100/250 MKIII by Simone Succi on Thu, 2026-02-26 08:28 |
by Simone Succi Thu, 2026-02-26 16:20 |
General discussion | ||
|
How different of VESC 6 and VESC 4 by Ken_chen on Thu, 2018-05-17 18:13 |
3 |
by ripperpc Mon, 2020-05-04 07:58 |
General discussion | |
|
Canbus slave control in duty cycle mode not working correctly by Enak on Sat, 2019-04-13 03:55 |
1 |
by benjamin Mon, 2019-04-15 10:09 |
General discussion | |
|
Could not read motor configuration during detection by siegele1 on Wed, 2023-08-02 17:17 |
1 |
by electricfox Thu, 2023-08-03 08:23 |
General discussion | |
|
Current control performance & best way to tune Kp and Ki by jinwonchung on Thu, 2024-10-17 15:52 |
by jinwonchung Thu, 2024-10-17 15:53 |
General discussion | ||
|
How can I add watts data to solidgeek? by Fixitmoditbreakit on Sat, 2021-06-12 00:07 |
2 |
by vadicus Tue, 2021-06-15 17:50 |
General discussion | |
|
Connecting handlebar controlls by mannberg on Thu, 2022-03-10 14:57 |
by mannberg Thu, 2022-03-10 14:57 |
General discussion |
Pages
