You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
how to update 4.0 firmware when only 5.0 and 5.1 firmware available by GSWconstruction on Mon, 2020-09-07 19:30 |
1 |
by frank Tue, 2020-09-22 09:18 |
General discussion | |
|
Focbox by macglen on Wed, 2024-03-27 22:45 |
1 |
by dpeinado Mon, 2024-04-15 17:51 |
VESC Firmware | |
|
Add another motor temperature sensor type (only minor tweak needed) by Henque19 on Wed, 2020-01-29 21:25 |
1 |
by Henque19 Wed, 2020-03-25 11:31 |
Feature Requests | |
|
PPM throttle detected in Vesc Tool but has no effect on motor by maxim1977 on Sat, 2025-07-26 06:03 |
1 |
by ftpkmarcelo Sun, 2025-08-10 06:07 |
VESC Tool | |
|
How I control the RPM of my motor from VESC with Arduino? by George W. on Sat, 2020-04-25 16:10 |
1 |
by frank Thu, 2020-04-30 18:16 |
General discussion | |
|
2nd Maytech 75_300 burned by Flyingtux on Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
General discussion | |
|
PPM Over limit settings. by marto on Thu, 2019-03-07 05:35 |
1 |
by marto Thu, 2019-03-07 08:36 |
VESC Firmware | |
|
Using VESC for Position Control of a Spring-Loaded Flapper Valve by Manny Vittal on Sat, 2026-05-30 15:20 |
1 |
by Manny Vittal Sat, 2026-05-30 15:21 |
Projects incorporating VESC technology | |
|
VESC TRAMPA NRF BLE firmware question and feature request by Spaceman on Sat, 2024-01-06 06:47 |
1 |
by Spaceman Sat, 2024-01-27 08:07 |
VESC Firmware | |
|
Flipsky 75200 + Flipsky 85135 12kw only 2kw output by giver on Thu, 2022-10-27 21:00 |
1 |
by skyline1970 Thu, 2022-11-24 20:08 |
Third Party Hardware | |
|
Wrong software shows up. Answered my own question. by leecon on Fri, 2025-03-07 17:50 |
1 |
by leecon Tue, 2025-03-11 17:00 |
General discussion | |
|
watt mode by Willoz600 on Tue, 2017-10-10 09:26 |
1 |
by frank Mon, 2017-10-16 20:58 |
Feature Requests | |
|
CAN_PACKET_STATUS_5 Current IN and Fault code by matrixgti on Tue, 2019-06-11 12:24 |
1 |
by STTS Fri, 2021-08-13 09:09 |
General discussion | |
|
PAS: constant torque control by afzalm on Thu, 2021-10-07 11:25 |
1 |
by TittyTwister Sun, 2022-07-10 12:43 |
Feature Requests | |
|
Can't get motor to run using COMM port on vesc 6 MKVI and arduino mega with a potentiometer and SolidGeeks UART library by Kokonenen on Thu, 2023-03-30 11:41 |
1 |
by Kokonenen Thu, 2023-03-30 16:19 |
General discussion | |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
|
Understanding VESC Hardware and $40 VESC target by ripperpc on Thu, 2020-02-27 06:41 |
1 |
by vadicus Mon, 2020-03-23 20:18 |
Third Party Hardware | |
|
Help Setup Flipsky FSESC 4.12 by R66 on Mon, 2025-09-29 05:23 |
1 |
by R66 Mon, 2025-09-29 06:58 |
General discussion | |
|
Brake rpm minimum by mcspikesky on Sat, 2023-07-22 22:51 |
1 |
by mcspikesky Tue, 2023-07-25 22:03 |
General discussion | |
|
Esc does not reply by nemethLali on Sun, 2021-08-01 16:07 |
1 |
by nemethLali Fri, 2021-08-06 22:18 |
Third Party Hardware |
Pages
