You are here
Active forum topics
Primary tabs
Topic | Replies |
Last post![]() |
Forum | |
---|---|---|---|---|
How does controlling two different motors over CAN bus really work? by oangelo on Sat, 2023-04-15 20:05 |
by oangelo Sat, 2023-04-15 20:05 |
General discussion | ||
HFI Mode Hoverboard Hub Motor by JulianT on Wed, 2023-04-12 19:16 |
by JulianT Sat, 2023-04-15 11:09 |
General discussion | ||
Position control of brushed dc motor with Vesc and REV through bore encoder by Greasy_D on Wed, 2023-03-29 20:17 |
14 |
by EnDeR_WiGiN Fri, 2023-04-14 17:48 |
General discussion | |
How to adjust ADC1 parameters to adjust the speed (not working) by player107 on Fri, 2023-04-14 13:46 |
by player107 Fri, 2023-04-14 13:46 |
VESC Tool | ||
GO-FOC G300 - shorted the USB connector shield to 72v by hedbrant on Tue, 2023-04-11 13:22 |
1 |
by hedbrant Thu, 2023-04-13 20:44 |
General discussion | |
vesc canbus control PPM by JiaheXu on Thu, 2023-04-13 20:17 |
by JiaheXu Thu, 2023-04-13 20:17 |
General discussion | ||
Position Limits w/ BDC and ABI Encoder by gokulswami on Thu, 2023-04-13 10:43 |
by gokulswami Thu, 2023-04-13 10:43 |
General discussion | ||
VESC as Generator - Low Output at High Brake Current? by hoeken on Sat, 2021-08-28 17:42 |
8 |
by flydr2 Wed, 2023-04-12 20:38 |
General discussion | |
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
Able to read CAN messages from VESC but cannot write messages to CAN Bus. by willd3543 on Wed, 2023-04-05 23:49 |
3 |
by benjamin Wed, 2023-04-12 07:32 |
General discussion | |
NEW and my motors sound like they work but hardly spin the wheels! by madurai85 on Sun, 2023-04-09 15:23 |
by madurai85 Sun, 2023-04-09 15:23 |
General discussion | ||
I have firmware question for a noob trying to get current firmware from 3.0 ver. and its not working! by madurai85 on Sun, 2023-04-09 15:12 |
by madurai85 Sun, 2023-04-09 15:12 |
VESC Firmware | ||
FLIPSKY FSESC 4.20 Mini Not Working! by Sacchit@123 on Sun, 2023-03-12 10:23 |
1 |
by player107 Fri, 2023-04-07 09:33 |
Third Party Hardware | |
Position control without encoder by bearing on Tue, 2023-04-04 18:45 |
1 |
by bearing Thu, 2023-04-06 22:07 |
VESC Tool | |
Slow UART at high current. by memeticmusic on Thu, 2023-03-30 21:33 |
2 |
by memeticmusic Thu, 2023-04-06 11:56 |
Projects incorporating VESC technology | |
How to control PPM output with CANBUS command by JiaheXu on Thu, 2023-03-30 20:21 |
2 |
by JiaheXu Wed, 2023-04-05 16:52 |
General discussion | |
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
FSESC 6.6 not Connecting to VESC Tool by billyredwood01 on Sat, 2020-11-28 12:34 |
12 |
by JP Mon, 2023-04-03 13:02 |
General discussion | |
VESC - custom board by st0r on Wed, 2023-03-08 12:21 |
5 |
by st0r Sat, 2023-04-01 01:51 |
General discussion | |
Trouble Downgrading to Firmware 5.03 by hdfghdfgh on Fri, 2023-03-31 22:10 |
by hdfghdfgh Fri, 2023-03-31 22:10 |
VESC Firmware |
Pages
