You are here
Active forum topics
Primary tabs
Topic |
Replies![]() |
Last post | Forum | |
---|---|---|---|---|
App. settings: "Enable servo output on PPM-port when PPM-app is disabled." option by alexantosh on Fri, 2021-12-10 09:46 |
by alexantosh Fri, 2021-12-10 09:46 |
VESC Tool | ||
move source and header files to a folder by Jimny on Thu, 2022-11-17 05:45 |
by Jimny Thu, 2022-11-17 05:45 |
General discussion | ||
Speed control issues w. hub motors by akerblad on Sun, 2019-04-07 17:22 |
by akerblad Sun, 2019-04-07 17:22 |
General discussion | ||
How to set up 60 degree hall sensors? by ryde6 on Sat, 2021-06-05 12:45 |
by ryde6 Sat, 2021-06-05 12:45 |
VESC Tool | ||
Best Throttle and break level by ardillolambo on Wed, 2022-03-02 18:29 |
by ardillolambo Wed, 2022-03-02 18:29 |
General discussion | ||
Modified version of mini4,during motor detection,fault_code_drv-11 was reported by qdxiatao on Mon, 2022-10-31 07:42 |
by qdxiatao Mon, 2022-10-31 07:42 |
Third Party Hardware | ||
DC MOTOR connected to FLIPSKY 4.20 MINI by CatalinCHIRICA on Mon, 2019-12-02 18:20 |
by CatalinCHIRICA Mon, 2019-12-02 18:20 |
VESC Tool | ||
VESC on Chromebook? by Boa1277 on Sun, 2021-02-21 20:49 |
by Boa1277 Sun, 2021-02-21 20:49 |
General discussion | ||
Abi encoder?? by Vigneshwar on Wed, 2019-11-20 06:10 |
by Vigneshwar Wed, 2019-11-20 06:10 |
Third Party Hardware | ||
Cheap remote from cheap board by Remind on Sun, 2021-08-15 02:06 |
by Remind Sun, 2021-08-15 02:06 |
Third Party Hardware | ||
servo input by Roger Wolff on Tue, 2018-07-03 07:50 |
by Roger Wolff Tue, 2018-07-03 07:50 |
VESC Firmware | ||
Freewheeling by Stianaj on Fri, 2020-01-17 19:15 |
by Stianaj Fri, 2020-01-17 19:15 |
VESC Tool | ||
24v Kobalt Powered Sunjoe Mower by mistersketchman on Sun, 2020-08-02 01:54 |
by mistersketchman Sun, 2020-08-02 01:55 |
Third Party Hardware | ||
Dual VESC via CAN by scholtylicious on Sat, 2021-03-13 15:56 |
by scholtylicious Sat, 2021-03-13 15:56 |
General discussion | ||
Problem with encoder readings with arduino by ruthvikchanda on Thu, 2018-12-06 07:06 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
General discussion | ||
help with vesc real time data trouble shooting by stefann on Wed, 2020-04-08 23:03 |
by stefann Wed, 2020-04-08 23:03 |
VESC Tool | ||
How to set a jog speed using an encoder by AK6302019 on Wed, 2019-08-07 15:42 |
by AK6302019 Wed, 2019-08-07 15:42 |
General discussion | ||
Dissimilar motor testing by geofrancis on Thu, 2022-02-24 16:54 |
by geofrancis Thu, 2022-02-24 16:57 |
General discussion | ||
Dollar signs break private messages by TechAUmNu on Tue, 2018-04-24 18:09 |
by TechAUmNu Tue, 2018-04-24 18:09 |
General discussion | ||
Update FW on multiple VESC pcbs using CAN issue by Offline on Thu, 2021-05-20 07:36 |
by Offline Thu, 2021-05-20 07:36 |
VESC Tool |
Pages
