You are here
Active forum topics
Primary tabs
| Topic | Replies | Last post |
Forum |
|
|---|---|---|---|---|
|
Flipsky 4.20 FOC settings Not Saving by erwinramos1010 on Mon, 2022-09-05 15:22 |
2 |
by wjpremerlani Sat, 2022-09-24 01:05 |
General discussion | |
|
More than 1A spike from the 5V 1A port of the VESC 6 HP by onluckyy on Thu, 2023-07-27 17:15 |
by onluckyy Thu, 2023-07-27 17:15 |
General discussion | ||
|
Read telemetry data from USB port by mlsc on Sun, 2024-10-06 22:01 |
by mlsc Sun, 2024-10-06 22:01 |
General discussion | ||
|
Large robot servo controller with VESC, how to set up position control by kisdia on Thu, 2024-09-19 17:47 |
by kisdia Thu, 2024-09-19 17:47 |
General discussion | ||
|
How to select COM port by Heimfried on Mon, 2020-05-04 22:23 |
3 |
by Heimfried Wed, 2020-06-10 11:55 |
General discussion | |
|
Install VESC on ubuntu 18.04 bionic by rest_vesc_001 on Tue, 2020-12-08 07:32 |
by rest_vesc_001 Fri, 2020-12-11 15:15 |
General discussion | ||
|
VESC 100/250 IO Ports Protection by luke.flecknell on Wed, 2022-03-30 06:49 |
2 |
by luke.flecknell Wed, 2022-03-30 12:41 |
General discussion | |
|
How to implement a simple autopilot by oangelo on Thu, 2022-12-22 12:50 |
by oangelo Thu, 2022-12-22 12:50 |
General discussion | ||
|
Current KP(Current controller proportional gain) by Geir Henriksen on Tue, 2019-04-30 10:51 |
1 |
by Ricardo Bosqui Tue, 2020-02-11 15:12 |
General discussion | |
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie on Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
General discussion | |
|
FSESC 75350 UNBALANCED_CURRENTS fault at higher loads by colmor on Thu, 2025-05-01 01:21 |
1 |
by erider Thu, 2025-10-09 07:55 |
General discussion | |
|
Safe Start of Hoverboard Motor by marc.s.cohn@gma... on Thu, 2020-07-23 01:39 |
1 |
by pf26 Thu, 2020-07-30 14:16 |
General discussion | |
|
Seeking Feedback: Controlling VESC via Web Interface by fjolivet on Sat, 2025-04-05 13:00 |
1 |
by fjolivet Mon, 2025-04-07 15:25 |
General discussion | |
|
At standstill a 30A limit? by Roger Wolff on Fri, 2017-11-17 09:37 |
2 |
by Roger Wolff Sat, 2017-11-18 11:58 |
General discussion | |
|
VESC settings for large scooter motor by trimen on Tue, 2020-07-14 22:15 |
10 |
by Juzy Tue, 2025-04-01 10:58 |
General discussion | |
|
large hub motors by Frankey on Sat, 2021-11-13 19:35 |
3 |
by spacewalker Tue, 2021-11-16 13:42 |
General discussion | |
|
VESC 100/250 by PBR-Automatyka on Tue, 2021-11-02 12:17 |
1 |
by PBR-Automatyka Tue, 2021-11-02 12:18 |
General discussion | |
|
Storing VESC Tool data for later analysis by AidanNowa on Wed, 2024-06-12 15:57 |
by AidanNowa Wed, 2024-06-12 15:57 |
General discussion | ||
|
Flipsky 75100 pro v2 ADC throttle stopped responding by JozoBozo on Tue, 2026-02-24 17:33 |
2 |
by JozoBozo Sun, 2026-03-01 13:40 |
General discussion | |
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist on Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
General discussion |
Pages
