You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Foc openloop soft start by Alan oldguy on Fri, 2018-09-07 03:05 |
by Alan oldguy Fri, 2018-09-07 03:05 |
Feature Requests | ||
|
VESC Software Understanding by shubhamt on Wed, 2018-08-22 15:40 |
by shubhamt Wed, 2018-08-22 15:40 |
General discussion | ||
|
Step/Dir signals by wall0069 on Sun, 2019-06-09 16:06 |
by wall0069 Sun, 2019-06-09 16:06 |
General discussion | ||
|
AHRS yaw drifting by henry10210 on Sun, 2020-02-09 01:13 |
by henry10210 Sun, 2020-02-09 01:13 |
VESC Firmware | ||
|
Limit Max RPM on a Brushed Motor in DC Mode by KirkusMaximus on Fri, 2020-09-04 02:52 |
by KirkusMaximus Fri, 2020-09-04 02:58 |
General discussion | ||
|
Single Flipsky FSESC 6.6 getting started and IMU data by alexantosh on Wed, 2021-04-07 12:32 |
by alexantosh Mon, 2021-11-15 13:10 |
Third Party Hardware | ||
|
Bafang BBSHD hub motor setup by csev-tcejorp on Sat, 2022-08-13 14:50 |
by csev-tcejorp Sat, 2022-08-13 14:50 |
Feature Requests | ||
|
Hard faults in mcpwm_foc.c? by vesc_fault on Thu, 2019-01-03 07:00 |
by vesc_fault Thu, 2019-01-03 07:20 |
VESC Firmware | ||
|
PT1000 on HW 4.12 by nickk on Tue, 2018-12-18 09:49 |
by nickk Tue, 2018-12-18 09:49 |
VESC Firmware | ||
|
Hoyt Puck Prototipo DSS50+ Firmware questions by tombell on Wed, 2020-04-29 03:56 |
by tombell Wed, 2020-04-29 03:56 |
General discussion | ||
|
Top Speed Hard Limit by sdobbie on Fri, 2021-06-18 23:31 |
by sdobbie Fri, 2021-06-18 23:31 |
Third Party Hardware | ||
|
VESC firmware to programmable Sabvoton ml60 controller. by Maciejwarloch on Tue, 2022-03-08 13:25 |
by Maciejwarloch Tue, 2022-03-08 13:25 |
VESC Firmware | ||
|
Which App to use and how to wire it by philboslaggins on Sat, 2022-11-05 16:20 |
by philboslaggins Sat, 2022-11-05 16:20 |
General discussion | ||
|
Phase A not working and GVDD_OV/GVDD_UV DRV faults by chocol4te on Mon, 2019-04-01 15:32 |
by chocol4te Mon, 2019-04-01 15:32 |
Third Party Hardware | ||
|
Firmware Updating to run X2 Pro remote for VESC6.6 by Caddy on Sat, 2020-06-27 19:30 |
by Caddy Sat, 2020-06-27 19:30 |
VESC Firmware | ||
|
Squealing noise and failed foc detection by sdobbie on Sat, 2021-10-23 17:00 |
by sdobbie Sun, 2021-10-24 20:05 |
VESC Development and Beta Testing | ||
|
Tuning process? by wingborne on Tue, 2020-09-29 00:09 |
by wingborne Tue, 2020-09-29 21:39 |
General discussion | ||
|
Is there a way to deactivate roll to start function FW 5.02 by Philo on Sun, 2021-04-11 13:55 |
by Philo Sun, 2021-04-11 13:58 |
Third Party Hardware | ||
|
id/iq Table input by red.blaylock on Fri, 2020-05-22 09:20 |
by red.blaylock Fri, 2020-05-22 12:11 |
Feature Requests | ||
|
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests |
Pages
