You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu on Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
VESC Firmware | |
|
will VESC synch with a 1020 inrunner? by Oded Mazor on Fri, 2022-02-18 16:58 |
1 |
by frank Fri, 2022-02-18 17:51 |
General discussion | |
|
Will a Flipsky FSESC4.20 50A Controller Work with Unknown Motor? by Laurie Forbes on Thu, 2021-09-30 21:31 |
1 |
by andyw2005 Fri, 2021-10-22 00:09 |
General discussion | |
|
Why use sensorless if the motor has sensors? by j.konrad on Thu, 2022-02-17 14:25 |
4 |
by j.konrad Mon, 2022-02-21 15:06 |
General discussion | |
|
why the motor current cant reach more than 2A? by chijay on Sat, 2021-03-13 16:38 |
1 |
by microcai Fri, 2021-08-13 14:50 |
VESC Development and Beta Testing | |
|
Why switchable current filters? by BillyJ on Sat, 2019-10-05 12:22 |
2 |
by shaman Sun, 2019-10-13 17:41 |
General discussion | |
|
Why such an old ChibiOS? by jackherer on Fri, 2021-04-16 17:03 |
1 |
by TechAUmNu Sat, 2021-04-17 00:51 |
VESC Firmware | |
|
Why not using interrupt for Hall signal detection? by kuan on Sun, 2021-01-03 09:51 |
by kuan Sun, 2021-01-03 09:51 |
General discussion | ||
|
Why Mosfet and Motor HW temp sensor schematic are different?! by ThierryGTLTS on Sat, 2017-09-09 10:13 |
3 |
by ThierryGTLTS Mon, 2017-09-11 12:50 |
VESC Original Hardware | |
|
Why is the speed lower in FOC mode than BLDC mode ? by stone_1706 on Thu, 2019-01-17 08:23 |
8 |
by speed3r Wed, 2022-06-15 09:34 |
General discussion | |
|
Why is my VESC Speed (in MPH) half what it should be? by ALarabie on Fri, 2022-12-09 17:41 |
6 |
by vadicus Sat, 2022-12-10 19:00 |
General discussion | |
|
Why i cant insert a topic? by SafrdA on Thu, 2021-04-29 20:41 |
by SafrdA Thu, 2021-04-29 20:41 |
General discussion | ||
|
Why don't BLDCs require PFC capacitors? by batdan on Mon, 2019-09-16 17:41 |
1 |
by DarioP Sun, 2020-11-22 16:43 |
General discussion | |
|
Why does the 75/300 have VCC at 3.4V? by TechAUmNu on Tue, 2020-03-31 14:01 |
3 |
by TechAUmNu Wed, 2020-09-02 12:04 |
VESC Original Hardware | |
|
Why android app doesn't save the BALANCE settings in the motors profile? Is it a BUG? by zmei116 on Sat, 2020-05-30 12:43 |
by zmei116 Sat, 2020-05-30 12:43 |
VESC Original Hardware | ||
|
Why android app doesn't save the BALANCE settings in the motors profile? Is it a BUG? by zmei116 on Fri, 2020-05-29 23:31 |
by zmei116 Fri, 2020-05-29 23:31 |
VESC Original Hardware | ||
|
Which to believe, manufacturer inductance spec or VESC autodetection? by kubark42 on Wed, 2021-09-29 15:59 |
3 |
by kubark42 Fri, 2021-10-22 20:01 |
General discussion | |
|
Which STM32F4 MCU's can be used? by nxtv2 on Sun, 2021-03-21 11:54 |
6 |
by TVAVAE Sat, 2021-07-10 00:40 |
Third Party Hardware | |
|
Which hall sensor should i buy? by qwerasdf on Sun, 2021-09-19 19:50 |
1 |
by skyline1970 Sat, 2021-10-30 16:00 |
Third Party Hardware | |
|
Which firmware do I need by Luka-Zagar on Tue, 2021-10-19 22:24 |
2 |
by Luka-Zagar Wed, 2021-10-20 19:38 |
VESC Firmware |
Pages
