You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
75300 IV Trampa schematic by MangoK on Tue, 2024-12-10 13:11 |
1 |
by Foujiwara Mon, 2025-03-17 04:38 |
VESC Original Hardware | |
|
75200 vesc by Zander rowley on Tue, 2021-10-12 21:53 |
1 |
by Zander rowley Tue, 2021-10-12 21:56 |
General discussion | |
|
75200 3.3 or 5v short circuit after 10 mins of use by Vassily on Thu, 2025-02-27 23:26 |
by Vassily Thu, 2025-02-27 23:26 |
General discussion | ||
|
75100 recognized as 75300 and nothing works by anaka on Mon, 2025-01-20 19:59 |
by anaka Mon, 2025-01-20 19:59 |
General discussion | ||
|
75100 ESC Hardware and firmware open source by ypl on Tue, 2022-02-08 16:21 |
5 |
by Artabotak Tue, 2024-04-16 20:36 |
Third Party Hardware | |
|
75/300 R3 with Original FW 4.2 can't update by nice2cu on Sun, 2020-06-14 17:26 |
1 |
by nice2cu Mon, 2020-06-15 20:41 |
VESC Original Hardware | |
|
75/300 R3 Power ON/OFF PINs and LED Status by nice2cu on Wed, 2020-06-17 17:35 |
by nice2cu Wed, 2020-06-17 17:37 |
VESC Original Hardware | ||
|
75/300 R3 and metr.at wird iOS metr App by nice2cu on Sun, 2020-09-13 20:51 |
by nice2cu Sun, 2020-09-13 20:51 |
VESC Original Hardware | ||
|
75/300 R2 FW higher than 3.62 ? it is possible? by Lasse on Sat, 2020-12-26 20:34 |
by Lasse Sat, 2020-12-26 20:34 |
VESC Firmware | ||
|
75/300 NRF Pairing by eptv on Sat, 2019-10-12 14:47 |
3 |
by frank Thu, 2019-12-05 11:22 |
VESC Original Hardware | |
|
75/300 Layout or gerbers by Chapel81 on Fri, 2020-08-28 21:27 |
3 |
by Chapel81 Wed, 2020-09-09 16:24 |
VESC Original Hardware | |
|
75/300 Large inrunner problem (video) by dk-odense on Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
General discussion | |
|
75/300 connection issues FW3.6 by renaudbarbier on Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
General discussion | |
|
75/250 question/issue by Petre Daniel Stroe on Sat, 2022-12-10 14:51 |
1 |
by frank Sat, 2022-12-10 21:13 |
General discussion | |
|
75 V 300 A only reading MOSFET temperature 1 in VESC Tool by ryanbohm on Thu, 2024-02-29 01:00 |
by ryanbohm Thu, 2024-02-29 01:00 |
VESC Original Hardware | ||
|
75 / 300 vesc by craig w on Thu, 2021-12-16 03:36 |
1 |
by electricfox Thu, 2021-12-16 15:29 |
General discussion | |
|
6MK6 Can Statusmessages by maxmertins on Fri, 2024-09-20 11:36 |
1 |
by Angelo99 Tue, 2025-01-07 10:18 |
VESC Tool | |
|
6.05 For IOS by NetworkDir on Tue, 2024-08-27 20:38 |
1 |
by electricfox Wed, 2024-08-28 07:14 |
VESC Tool | |
|
6 Phase Motor - How to Drive it? by vitormhenrique on Wed, 2020-02-19 05:47 |
2 |
by Badkad Fri, 2020-03-20 19:36 |
General discussion | |
|
5V/serial weirdness when using FOC by wihrl on Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
General discussion |
Pages
