You are here
Active forum topics
Primary tabs
Topic |
Replies | Last post | Forum | |
|---|---|---|---|---|
|
Advice please - VESC6 controller for a specific model aircraft application by aabill on Wed, 2019-11-27 11:31 |
5 |
by frank Sun, 2019-12-01 17:28 |
General discussion | |
|
Advice on using the VESC 100/250 vs Kelly Controller for 10 kW motorboat by Pilotniq on Fri, 2020-10-23 22:06 |
1 |
by skyline1970 Sun, 2020-10-25 10:29 |
General discussion | |
|
advice on position control by feskarn on Mon, 2021-02-15 14:47 |
by feskarn Mon, 2021-02-15 14:47 |
General discussion | ||
|
Advanced settings for FOC motor detection (flux linkage) by jaghori.sasan on Sun, 2019-02-17 09:34 |
2 |
by jaghori.sasan Sun, 2019-02-17 17:51 |
VESC Tool | |
|
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
|
Adjusting Acceleration Ramp with NRF & Current control by Mido on Tue, 2022-04-05 14:36 |
by Mido Tue, 2022-04-05 14:36 |
General discussion | ||
|
adiv5.h adiv5_dp_abort function confusion by dsppower on Sun, 2022-05-08 19:26 |
by dsppower Sun, 2022-05-08 19:26 |
VESC Firmware | ||
|
Additional Status Messages by louisgcr on Tue, 2021-12-21 08:04 |
by louisgcr Tue, 2021-12-21 08:04 |
General discussion | ||
|
Adding two reed contacts and adapting the software accordingly by WulfKraneis on Sun, 2020-09-06 16:25 |
1 |
by district9prawn Fri, 2020-09-11 13:15 |
Feature Requests | |
|
Adding support for three phase shunts... by Roger Wolff on Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
VESC Firmware | |
|
Adding Openloop Com Comand and Temp. Measurement via Resistance by JulianT on Mon, 2022-10-03 11:32 |
by JulianT Mon, 2022-10-03 11:32 |
Feature Requests | ||
|
Adding more temperature sensors via I2C by telltower_IV on Fri, 2021-06-04 01:32 |
1 |
by vadicus Fri, 2021-06-04 05:37 |
VESC Development and Beta Testing | |
|
Adding HM-10 Compatibility with Small Changes to Code by Jfriesen on Sat, 2018-06-09 00:45 |
5 |
by CTSchorsch Mon, 2020-01-06 07:11 |
VESC Tool | |
|
adding electronic freewheel function by ceejaye on Mon, 2019-09-02 17:30 |
3 |
by mnmsmushy Wed, 2020-09-23 02:32 |
Feature Requests | |
|
Adding capacitors with long power cables? by rich on Thu, 2017-09-07 20:40 |
6 |
by frank Mon, 2018-08-20 09:12 |
VESC Original Hardware | |
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
Feature Requests | |
|
Adding a Openloop COMM Comand by JulianT on Sun, 2021-01-17 21:27 |
2 |
by JulianT Mon, 2021-02-15 12:17 |
General discussion | |
|
Add support for dual H3LIS331DL accelerometer by SirPolPol on Fri, 2022-04-08 09:09 |
3 |
by frank Mon, 2022-04-11 09:08 |
Feature Requests | |
|
Add support for AS5x47U encoder by ZachOB on Wed, 2022-04-27 00:50 |
1 |
by ZachOB Mon, 2022-07-18 23:42 |
VESC Development and Beta Testing | |
|
Add SPI encoder reading (in addition of the hall sensor) by Mounir on Fri, 2023-03-03 16:04 |
1 |
by frank Wed, 2023-03-15 13:58 |
VESC Firmware |
Pages
